GEUTEBRUCKGEVISCOPE actions overview english v. 2.95, September 5, 2013 Dmitri Schamschurko DRAFT for internal use only GEUTEBR ¨UCK GmbH Im Nassen 7–9 D–53578 Windhagen Deutschland Tel: +49 (0) 2645/137–0 Fax: +49 (0) 2645/137–999 Web: www.geutebrueck.de --- Page 1 --- Abstract This document gives an overview about GEVISCOPE actions in the current version 2.95 from September 5, 2013. This document is part of the GEVISCOPE SDK. Disclaimer All possible care has been used to assure the information contained in this specifi- cation is as accurate and complete as possible. However, the author reserves the rights not to be responsible for the topicality, correctness, completeness or qual- ity of the information provided, and therefore is not liable for any damage caused by the use of any information provided, including any kind of information which is incomplete or incorrect. The author reserves the rights to extend, change or delete parts or the complete publication without separate announcement. --- Page 2 --- GEUTEBRUCKContents 1 General 15 1.1 Used notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1.2 Action classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2 ATM/ACS 16 2.1 ACS access denied . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2.2 ACS access granted . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.3 ACS raw answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.4 ACS raw data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.5 ATM raw answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.6 ATM raw data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.7 ATM transaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3 Audio control 18 3.1 ABC connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.2 ABC disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.3 ABC play file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3.4 Sensor audio alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4 Backup actions 19 4.1 Abort all auto backups . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.2 Abort auto backup . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.3 Auto backup capacity file auto deleted . . . . . . . . . . . . . . . . 19 4.4 Auto backup capacity out of disk space . . . . . . . . . . . . . . . . 20 4.5 Auto backup capacity warning . . . . . . . . . . . . . . . . . . . . . 20 4.6 Auto backup file done . . . . . . . . . . . . . . . . . . . . . . . . . 21 4.7 Auto backup file progress . . . . . . . . . . . . . . . . . . . . . . . 21 4.8 Auto backup file started . . . . . . . . . . . . . . . . . . . . . . . . 22 4.9 Auto backup operation done . . . . . . . . . . . . . . . . . . . . . . 22 4.10 Auto backup operation started . . . . . . . . . . . . . . . . . . . . . 23 4.11 Auto backup schedule done . . . . . . . . . . . . . . . . . . . . . . 23 4.12 Auto backup schedule started . . . . . . . . . . . . . . . . . . . . . 23 4.13 Backup event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 4.14 Event backup done . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 3 --- Page 3 --- GEUTEBRUCK4.15 Event backup file done . . . . . . . . . . . . . . . . . . . . . . . . . 24 4.16 Event backup file progress . . . . . . . . . . . . . . . . . . . . . . . 25 4.17 Event backup file started . . . . . . . . . . . . . . . . . . . . . . . . 25 4.18 Event backup started . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.19 Start auto backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 5 Camera control 26 5.1 Auto focus off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 5.2 Auto focus on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 5.3 Camera RAW output . . . . . . . . . . . . . . . . . . . . . . . . . . 26 5.4 Camera apply profile . . . . . . . . . . . . . . . . . . . . . . . . . . 26 5.5 Camera backlight compensation mode . . . . . . . . . . . . . . . . 26 5.6 Camera clear preset text . . . . . . . . . . . . . . . . . . . . . . . . 27 5.7 Camera day/night mode . . . . . . . . . . . . . . . . . . . . . . . . 27 5.8 Camera light off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.9 Camera light on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.10 Camera manual iris off . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.11 Camera manual iris on . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.12 Camera off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.13 Camera on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 5.14 Camera pump off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 5.15 Camera pump on . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 5.16 Camera select char mode . . . . . . . . . . . . . . . . . . . . . . . 28 5.17 Camera set preset text . . . . . . . . . . . . . . . . . . . . . . . . . 28 5.18 Camera spec func U off . . . . . . . . . . . . . . . . . . . . . . . . 28 5.19 Camera spec func U on . . . . . . . . . . . . . . . . . . . . . . . . 28 5.20 Camera spec func V off . . . . . . . . . . . . . . . . . . . . . . . . 29 5.21 Camera spec func V on . . . . . . . . . . . . . . . . . . . . . . . . 29 5.22 Camera spec func X off . . . . . . . . . . . . . . . . . . . . . . . . 29 5.23 Camera spec func X on . . . . . . . . . . . . . . . . . . . . . . . . 29 5.24 Camera spec func Y off . . . . . . . . . . . . . . . . . . . . . . . . 29 5.25 Camera spec func Y on . . . . . . . . . . . . . . . . . . . . . . . . 29 5.26 Camera stop all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 5.27 Camera text off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 5.28 Camera text on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 4 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 4 --- GEUTEBRUCK5.29 Camera tour start . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 5.30 Camera tour stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 5.31 Camera version off . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 5.32 Camera version on . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 5.33 Camera wash-wipe off . . . . . . . . . . . . . . . . . . . . . . . . . 30 5.34 Camera wash-wipe on . . . . . . . . . . . . . . . . . . . . . . . . . 31 5.35 Clear default position . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5.36 Clear preset position . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5.37 Fast speed off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5.38 Fast speed on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5.39 Focus far . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5.40 Focus near . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5.41 Focus stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 5.42 Iris close . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 5.43 Iris open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 5.44 Iris stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 5.45 Move by speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 5.46 Move to absolute position . . . . . . . . . . . . . . . . . . . . . . . 32 5.47 Move to default position . . . . . . . . . . . . . . . . . . . . . . . . 33 5.48 Move to preset position . . . . . . . . . . . . . . . . . . . . . . . . 33 5.49 Move to relative position . . . . . . . . . . . . . . . . . . . . . . . . 33 5.50 Pan auto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 5.51 Pan left . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 5.52 Pan right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 5.53 Pan stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5.54 Save default position . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5.55 Save preset position . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5.56 Set camera text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5.57 Tilt down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5.58 Tilt stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5.59 Tilt up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 5.60 Zoom in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 5.61 Zoom out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 5.62 Zoom stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 5 --- Page 5 --- GEUTEBRUCK6 Cash management actions 35 6.1 Safebag close . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 6.2 Safebag data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 6.3 Safebag open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 6.4 Safebag passing of risk data . . . . . . . . . . . . . . . . . . . . . . 37 6.5 Safebag passing of risk start . . . . . . . . . . . . . . . . . . . . . 37 6.6 Safebag passing of risk stop . . . . . . . . . . . . . . . . . . . . . . 37 7 Device information 38 7.1 Device found . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 7.2 Device plugin error . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 7.3 Device plugin state . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 7.4 Device reattached . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 7.5 Device removed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 7.6 New firmware received . . . . . . . . . . . . . . . . . . . . . . . . . 39 8 Digital contacts 40 8.1 Case has been closed . . . . . . . . . . . . . . . . . . . . . . . . . 40 8.2 Case has been opened . . . . . . . . . . . . . . . . . . . . . . . . 40 8.3 Digital input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 8.4 IOI43 reset mainboard . . . . . . . . . . . . . . . . . . . . . . . . . 40 8.5 IOI43 temperature notification . . . . . . . . . . . . . . . . . . . . . 40 8.6 IOI43 watchdog activate . . . . . . . . . . . . . . . . . . . . . . . . 40 8.7 IOI43 watchdog deactivate . . . . . . . . . . . . . . . . . . . . . . . 41 8.8 IOI43 watchdog trigger . . . . . . . . . . . . . . . . . . . . . . . . . 41 8.9 Key pressed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 8.10 Key released . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 8.11 Reset mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 8.12 Set digital output . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 8.13 Set system LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 8.14 Set system LED to blink . . . . . . . . . . . . . . . . . . . . . . . . 42 8.15 Temperature notification . . . . . . . . . . . . . . . . . . . . . . . . 42 8.16 Watchdog activate . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 8.17 Watchdog deactivate . . . . . . . . . . . . . . . . . . . . . . . . . . 42 8.18 Watchdog trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 6 --- GEUTEBRUCK9 Imex 42 9.1 Imex capacity file auto deleted . . . . . . . . . . . . . . . . . . . . 43 9.2 Imex capacity out of disk space. . . . . . . . . . . . . . . . . . . . . 43 9.3 Imex capacity warning . . . . . . . . . . . . . . . . . . . . . . . . . 43 9.4 Imex export event image . . . . . . . . . . . . . . . . . . . . . . . . 44 9.5 Imex export image from DB . . . . . . . . . . . . . . . . . . . . . . 44 9.6 Imex export image from live stream . . . . . . . . . . . . . . . . . . 44 10 LPS 44 10.1 LPS position data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 10.2 LPS query position . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 11 Lenel 45 11.1 Lenel access event . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 11.2 Lenel fire event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 11.3 Lenel intercom event . . . . . . . . . . . . . . . . . . . . . . . . . . 47 11.4 Lenel raw data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 11.5 Lenel refresh names . . . . . . . . . . . . . . . . . . . . . . . . . . 47 11.6 Lenel security event . . . . . . . . . . . . . . . . . . . . . . . . . . 48 11.7 Lenel video event . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 12 POS 49 12.1 Barcode data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 12.2 Filling pump status . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 12.3 Interface raw answer . . . . . . . . . . . . . . . . . . . . . . . . . . 49 12.4 Interface raw data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 12.5 POS data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 12.6 POS status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 12.7 Terminal article data . . . . . . . . . . . . . . . . . . . . . . . . . . 50 12.8 Terminal payment data . . . . . . . . . . . . . . . . . . . . . . . . . 51 13 Perimeter protection 51 13.1 PP device alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 13.2 PP device input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 13.3 PP device offline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 13.4 PP device online . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 7 --- Page 7 --- GEUTEBRUCK13.5 PP interface offline . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 13.6 PP interface online . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 13.7 PP query interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 13.8 PP set device output . . . . . . . . . . . . . . . . . . . . . . . . . . 52 13.9 PP subcell alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 13.10 PP zone alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 14 Remote export 53 14.1 Cancel export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 14.2 Export finished . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 14.3 Export progress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 14.4 Initialize remote export . . . . . . . . . . . . . . . . . . . . . . . . . 54 14.5 Set export marker . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 14.6 Start remote export . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 14.7 Start scene store . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 15 SKIDATA 55 15.1 SKIDATA control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 15.2 SKIDATA device event . . . . . . . . . . . . . . . . . . . . . . . . . 55 15.3 SKIDATA entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 15.4 SKIDATA exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 15.5 SKIDATA transaction . . . . . . . . . . . . . . . . . . . . . . . . . . 56 16 Supply chain security 56 16.1 GSCS vehicle access denied . . . . . . . . . . . . . . . . . . . . . 56 16.2 GSCS vehicle access expired . . . . . . . . . . . . . . . . . . . . . 56 16.3 GSCS vehicle access granted . . . . . . . . . . . . . . . . . . . . . 57 16.4 GSCS vehicle access pending . . . . . . . . . . . . . . . . . . . . 57 16.5 Log NPR recognition . . . . . . . . . . . . . . . . . . . . . . . . . . 58 16.6 Log barcode data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 16.7 Log barcode data LPS . . . . . . . . . . . . . . . . . . . . . . . . . 58 17 System actions 59 17.1 Blocking filter activate . . . . . . . . . . . . . . . . . . . . . . . . . 59 17.2 Blocking filter deactivate . . . . . . . . . . . . . . . . . . . . . . . . 59 17.3 Custom action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 8 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 8 --- GEUTEBRUCK17.4 Database recording info per ring . . . . . . . . . . . . . . . . . . . 60 17.5 Database recording info total . . . . . . . . . . . . . . . . . . . . . 60 17.6 Database started . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 17.7 Event recording changed . . . . . . . . . . . . . . . . . . . . . . . 61 17.8 Event started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 17.9 Event stopped . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 17.10 FRC notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 17.11 GEMOS alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 17.12 IP switch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 17.13 Kill all events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 17.14 Kill event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 17.15 Kill event by instance . . . . . . . . . . . . . . . . . . . . . . . . . . 62 17.16 Live check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 17.17 Redundant power failure . . . . . . . . . . . . . . . . . . . . . . . . 63 17.18 Redundant power ok . . . . . . . . . . . . . . . . . . . . . . . . . . 63 17.19 SMRP viewer cleared . . . . . . . . . . . . . . . . . . . . . . . . . 63 17.20 SMRP viewer connected . . . . . . . . . . . . . . . . . . . . . . . . 63 17.21 SMTP mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 17.22 Set clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 17.23 Set watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 17.24 Setup changed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 17.25 Setup upload progress . . . . . . . . . . . . . . . . . . . . . . . . . 64 17.26 Start event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 17.27 Stop all events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 17.28 Stop event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 17.29 Stop event by instance . . . . . . . . . . . . . . . . . . . . . . . . . 65 17.30 System error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 17.31 System info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 17.32 System settings changed . . . . . . . . . . . . . . . . . . . . . . . 66 17.33 System started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 17.34 System terminating . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 17.35 System warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 17.36 Transfer binary buffer . . . . . . . . . . . . . . . . . . . . . . . . . . 67 17.37 Transfer binary channel buffer . . . . . . . . . . . . . . . . . . . . . 67 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 9 --- Page 9 --- GEUTEBRUCK17.38 User login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 17.39 User login failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 17.40 User logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 18 Video control 68 18.1 Activate external process . . . . . . . . . . . . . . . . . . . . . . . 68 18.2 CPA measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 18.3 Change AD parameter set . . . . . . . . . . . . . . . . . . . . . . . 68 18.4 Change CPA parameter set . . . . . . . . . . . . . . . . . . . . . . 69 18.5 Change GTectVMX parameter set . . . . . . . . . . . . . . . . . . 69 18.6 Change OBTRACK parameter set . . . . . . . . . . . . . . . . . . 69 18.7 Change VMD parameter set . . . . . . . . . . . . . . . . . . . . . . 69 18.8 Change camera profile . . . . . . . . . . . . . . . . . . . . . . . . . 69 18.9 Channel error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 18.10 Channel info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 18.11 Channel live check . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 18.12 Channel warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 18.13 Enable client VCA . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 18.14 G-Tect analytics live check . . . . . . . . . . . . . . . . . . . . . . . 71 18.15 G-Tect scene alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 18.16 G-Tect scene alarm finished . . . . . . . . . . . . . . . . . . . . . . 71 18.17 G-Tect/Dual sensor alarm . . . . . . . . . . . . . . . . . . . . . . . 71 18.18 G-Tect/Dual sensor alarm finished . . . . . . . . . . . . . . . . . . 72 18.19 G-Tect/VMX alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 18.20 G-Tect/VMX alarm finished . . . . . . . . . . . . . . . . . . . . . . 72 18.21 IAS settings changed . . . . . . . . . . . . . . . . . . . . . . . . . . 72 18.22 IP camera failover notification . . . . . . . . . . . . . . . . . . . . . 72 18.23 IP camera failover restore . . . . . . . . . . . . . . . . . . . . . . . 73 18.24 IP camera raw command . . . . . . . . . . . . . . . . . . . . . . . 73 18.25 Make CPA reference image . . . . . . . . . . . . . . . . . . . . . . 73 18.26 Media channel setup . . . . . . . . . . . . . . . . . . . . . . . . . . 73 18.27 NPR raw data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 18.28 NPR recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 18.29 OBTRACK channel counter . . . . . . . . . . . . . . . . . . . . . . 75 18.30 OBTRACK channel counter threshold . . . . . . . . . . . . . . . . 75 10 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 10 --- GEUTEBRUCK18.31 OBTRACK channel set counter . . . . . . . . . . . . . . . . . . . . 75 18.32 OBTRACK frame raw data . . . . . . . . . . . . . . . . . . . . . . . 75 18.33 OBTRACK group counter . . . . . . . . . . . . . . . . . . . . . . . 76 18.34 OBTRACK group counter threshold . . . . . . . . . . . . . . . . . . 76 18.35 OBTRACK group set counter . . . . . . . . . . . . . . . . . . . . . 76 18.36 OBTRACK object raw data . . . . . . . . . . . . . . . . . . . . . . . 77 18.37 OBTRACK tunnel alarm . . . . . . . . . . . . . . . . . . . . . . . . 77 18.38 Sensor alarm finished . . . . . . . . . . . . . . . . . . . . . . . . . 77 18.39 Sensor inhibit alarm finished . . . . . . . . . . . . . . . . . . . . . . 78 18.40 Sensor inhibit video alarm . . . . . . . . . . . . . . . . . . . . . . . 78 18.41 Sensor video alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 18.42 Set system time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 18.43 Set test picture mode . . . . . . . . . . . . . . . . . . . . . . . . . . 79 18.44 VCA set armed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 18.45 VCA status answer . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 18.46 VCA status request . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 18.47 Video contrast detected . . . . . . . . . . . . . . . . . . . . . . . . 79 18.48 Video contrast failed . . . . . . . . . . . . . . . . . . . . . . . . . . 80 18.49 Video set image brightness . . . . . . . . . . . . . . . . . . . . . . 80 18.50 Video set image contrast . . . . . . . . . . . . . . . . . . . . . . . . 80 18.51 Video set image saturation . . . . . . . . . . . . . . . . . . . . . . . 80 18.52 Video source has changed . . . . . . . . . . . . . . . . . . . . . . 80 18.53 Video sync detected . . . . . . . . . . . . . . . . . . . . . . . . . . 81 18.54 Video sync failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 19 Viewer actions 81 19.1 VC alarm queue confirm . . . . . . . . . . . . . . . . . . . . . . . . 81 19.2 VC alarm queue confirm by instance . . . . . . . . . . . . . . . . . 81 19.3 VC alarm queue confirm by type . . . . . . . . . . . . . . . . . . . 81 19.4 VC alarm queue remove . . . . . . . . . . . . . . . . . . . . . . . . 82 19.5 VC alarm queue remove by instance . . . . . . . . . . . . . . . . . 82 19.6 VC alarm queue remove by type . . . . . . . . . . . . . . . . . . . 82 19.7 VC alarm queue select . . . . . . . . . . . . . . . . . . . . . . . . . 82 19.8 VC alarm queue select by instance . . . . . . . . . . . . . . . . . . 82 19.9 VC alarm queue select by type . . . . . . . . . . . . . . . . . . . . 82 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 11 --- Page 11 --- GEUTEBRUCK19.10 VC change scene by name . . . . . . . . . . . . . . . . . . . . . . 83 19.11 VC clear scene by name . . . . . . . . . . . . . . . . . . . . . . . . 83 19.12 VC full mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 19.13 VC set audio level . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 19.14 VC show viewer text . . . . . . . . . . . . . . . . . . . . . . . . . . 83 19.15 VC stretch mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 19.16 Viewer change scene . . . . . . . . . . . . . . . . . . . . . . . . . 84 19.17 Viewer change sync audio/video . . . . . . . . . . . . . . . . . . . 84 19.18 Viewer clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 19.19 Viewer clear scene . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 19.20 Viewer clear text output . . . . . . . . . . . . . . . . . . . . . . . . 84 19.21 Viewer connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 19.22 Viewer connect live . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 19.23 Viewer export picture . . . . . . . . . . . . . . . . . . . . . . . . . . 85 19.24 Viewer jump by time . . . . . . . . . . . . . . . . . . . . . . . . . . 85 19.25 Viewer maximize . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 19.26 Viewer play from time . . . . . . . . . . . . . . . . . . . . . . . . . 85 19.27 Viewer print picture . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 19.28 Viewer select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 19.29 Viewer set play mode . . . . . . . . . . . . . . . . . . . . . . . . . . 86 19.30 Viewer show alarm by instance . . . . . . . . . . . . . . . . . . . . 86 19.31 Viewer show alarm by key . . . . . . . . . . . . . . . . . . . . . . . 86 19.32 Viewer show alarm by type . . . . . . . . . . . . . . . . . . . . . . 87 19.33 Viewer text output . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 20 Viewer notifications 87 20.1 Image export notification . . . . . . . . . . . . . . . . . . . . . . . . 87 20.2 Scene store modification . . . . . . . . . . . . . . . . . . . . . . . . 88 20.3 VC alarm queue notification . . . . . . . . . . . . . . . . . . . . . . 88 20.4 VC scene changed . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 20.5 Viewer cleared . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 20.6 Viewer connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 20.7 Viewer play mode changed . . . . . . . . . . . . . . . . . . . . . . 89 20.8 Viewer selection changed . . . . . . . . . . . . . . . . . . . . . . . 89 A Examples 90 12 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 12 --- GEUTEBRUCKIndex 107 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 13 --- Page 13 --- GEUTEBRUCK14 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 14 --- GEUTEBRUCK1 General 1.1 Used notation This section explains the notation used in this publication. Consider the action ‘ User login ’. This action is described by the following section: 17.38 User login This action will be fired when the user has connected to the system. first user – Name of the user connected to the system. second user – Name of the second user by four eyes authentication. remote host – Host from where the connection is done. client host – Host from where the connection is done. client type – Client type. client account – User account from where the connection is done. The section heading – User login – gives the plain name of the action. The line below describes the action briefly. The list of parameters – if any – completes the section. For every action’s parame- ter its plain name – first user , and its description are given. Optional parameters are marked by rednames. 1.2 Action classes All GEVISCOPE actions are divided into the following action classes: ATM/ACS ATM and ACS actions. Audio control All actions to control the audio streams, also all notifications about the state change of the audio streams. Backup actions All actions for backup. Camera control All actions to remote control the PTZ heads or camera adjustments. Cash management actions All actions for cash management. Device information All actions for low-level notification of the device or media channels changes. Digital contacts All actions for handling digital inputs and outputs. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 15 --- Page 15 --- GEUTEBRUCKImex Image export. LPS LPS messages. Lenel Lenel. POS POS (point of sale). Perimeter protection Perimeter protection. Remote export Remote export. SKIDATA SKIDATA messages. Supply chain security Supply chain security. System actions All actions describing system behaviour. Video control All actions to control the video streams, also all notifications about the state change of the video streams. Viewer actions All actions for viewer customizing. Viewer notifications All viewer notifications. 2 ATM/ACS ATM and ACS actions. 2.1 ACS access denied ACS access denied. ACS – ACS name. ACS no – ACS no. account – Account no. bank code – Bank code. card no – Card no. time stamp – Time stamp. reason – Reason. 16 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 16 --- GEUTEBRUCK2.2 ACS access granted ACS access granted. ACS – ACS name. ACS no – ACS no. account – Account no. bank code – Bank code. card no – Card no. time stamp – Time stamp. 2.3 ACS raw answer ACS raw answer. ACS – ACS name. time stamp – Time stamp. answer – ACS answer. 2.4 ACS raw data ACS raw data. ACS – ACS name. time stamp – Time stamp. data – ACS data. 2.5 ATM raw answer ATM raw answer. ATM – ATM name. time stamp – Time stamp. answer – ATM answer. 2.6 ATM raw data ATM raw data. ATM – ATM name. time stamp – Time stamp. data – ATM data. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 17 --- Page 17 --- GEUTEBRUCK2.7 ATM transaction ATM transaction. ATM – ATM name. new transaction – New transaction. photostep – Photostep. ATM no – ATM no. account – Account no. bank code – Bank code. card no – Card no. tan 1 – TAN 1. tan 2 – TAN 2. time stamp 1 – Time stamp 1. time stamp 2 – Time stamp 2. amount – Amount. currency – Currency. 3 Audio control All actions to control the audio streams, also all notifications about the state change of the audio streams. 3.1 ABC connect Connect audio back channel. address – Address of the remote server. 3.2 ABC disconnect Disconnect audio back channel. This action has no parameters. 18 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 18 --- GEUTEBRUCK3.3 ABC play file Play file on audio back channel. file ID – File ID. file name – Name of the file. repeat – Repeat file automatically 3.4 Sensor audio alarm Audio alarm detected. channel – Channel. 4 Backup actions All actions for backup. 4.1 Abort all auto backups Abort all auto backups. This action has no parameters. 4.2 Abort auto backup Abort auto backup. schedule – Schedule. 4.3 Auto backup capacity file auto deleted Auto backup capacity monitoring: file auto deleted. warning – Warning. destination – Destination. total capacity – Total capacity. free capacity – Free capacity. allocated by GBF – Allocated by GBF . percent free – Percent free. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 19 --- Page 19 --- GEUTEBRUCKpercent allocated – Percent allocated. percent allocated by GBF – Percent allocated by GBF . file size – File size. file name – File name. 4.4 Auto backup capacity out of disk space Auto backup capacity monitoring: out of disk space. warning – Warning. destination – Destination. total capacity – Total capacity. free capacity – Free capacity. allocated by GBF – Allocated by GBF . percent free – Percent free. percent allocated – Percent allocated. percent allocated by GBF – Percent allocated by GBF . 4.5 Auto backup capacity warning Auto backup capacity monitoring: capacity warning. warning – Warning. destination – Destination. total capacity – Total capacity. free capacity – Free capacity. allocated by GBF – Allocated by GBF . percent free – Percent free. percent allocated – Percent allocated. percent allocated by GBF – Percent allocated by GBF . 20 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 20 --- GEUTEBRUCK4.6 Auto backup file done Auto backup progress notification: file done. schedule – Schedule. start time – Start time, empty during event backup. effective start time – Effective schedule start time. operation count – Operation count. timer start – Timer start. operation index – Operation index. operation start time – Operation start time. source – Source. destination – Destination. file size limit – File size limit. band width limit – Band width limit. file index – File index. file name – File name. file size – File size. 4.7 Auto backup file progress Auto backup progress notification: file progress. schedule – Schedule. start time – Start time, empty during event backup. effective start time – Effective schedule start time. operation count – Operation count. timer start – Timer start. operation index – Operation index. operation start time – Operation start time. source – Source. destination – Destination. file size limit – File size limit. band width limit – Band width limit. file index – File index. file name – File name. file size – File size. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 21 --- Page 21 --- GEUTEBRUCK4.8 Auto backup file started Auto backup progress notification: file started. schedule – Schedule. start time – Start time, empty during event backup. effective start time – Effective schedule start time. operation count – Operation count. timer start – Timer start. operation index – Operation index. operation start time – Operation start time. source – Source. destination – Destination. file size limit – File size limit. band width limit – Band width limit. file index – File index. file name – File name. 4.9 Auto backup operation done Auto backup progress notification: operation done. schedule – Schedule. start time – Start time, empty during event backup. effective start time – Effective schedule start time. operation count – Operation count. timer start – Timer start. operation index – Operation index. operation start time – Operation start time. operation stop time – Operation stop time. source – Source. destination – Destination. file size limit – File size limit. band width limit – Band width limit. error code – Operation error code. 22 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 22 --- GEUTEBRUCK4.10 Auto backup operation started Auto backup progress notification: operation started. schedule – Schedule. start time – Start time, empty during event backup. effective start time – Effective schedule start time. operation count – Operation count. timer start – Timer start. operation index – Operation index. operation start time – Operation start time. source – Source. destination – Destination. file size limit – File size limit. band width limit – Band width limit. 4.11 Auto backup schedule done Auto backup progress notification: schedule done. schedule – Schedule. start time – Start time, empty during event backup. effective start time – Effective schedule start time. stop time – Schedule stop time. operation count – Operation count. timer start – Timer start. 4.12 Auto backup schedule started Auto backup progress notification: schedule started. schedule – Schedule. start time – Start time, empty during event backup. effective start time – Effective schedule start time. operation count – Operation count. timer start – Timer start. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 23 --- Page 23 --- GEUTEBRUCK4.13 Backup event Backup event. instance ID – Instance ID of the event. event type – Type of the event. destination – Destination. start hint ID – Optional start hint ID. stop hint ID – Optional stop hint ID. sub folder – Sub folder to backup event. 4.14 Event backup done Event backup progress notification: backup done. job ID – Backup job ID. event type – Type of the event. instance ID – Instance ID of the event. destination – Destination. file size limit – File size limit. band width limit – Band width limit. start time – Backup start time. stop time – Backup stop time. error code – Operation error code. 4.15 Event backup file done Event backup progress notification: file done. job ID – Backup job ID. event type – Type of the event. instance ID – Instance ID of the event. destination – Destination. file size limit – File size limit. band width limit – Band width limit. start time – Effective backup start time. file index – File index. file name – File name. file size – File size. 24 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 24 --- GEUTEBRUCK4.16 Event backup file progress Event backup progress notification: file progress. job ID – Backup job ID. event type – Type of the event. instance ID – Instance ID of the event. destination – Destination. file size limit – File size limit. band width limit – Band width limit. start time – Effective backup start time. file index – File index. file name – File name. file size – File size. 4.17 Event backup file started Event backup progress notification: file started. job ID – Backup job ID. event type – Type of the event. instance ID – Instance ID of the event. destination – Destination. file size limit – File size limit. band width limit – Band width limit. start time – Effective backup start time. file index – File index. file name – File name. 4.18 Event backup started Event backup progress notification: backup started. job ID – Backup job ID. event type – Type of the event. instance ID – Instance ID of the event. destination – Destination. file size limit – File size limit. band width limit – Band width limit. start time – Backup start time. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 25 --- Page 25 --- GEUTEBRUCK4.19 Start auto backup Start auto backup. schedule – Schedule. 5 Camera control All actions to remote control the PTZ heads or camera adjustments. 5.1 Auto focus off Disable auto focus of the camera. PTZ head – PTZ head. 5.2 Auto focus on Enable auto focus of the camera. PTZ head – PTZ head. 5.3 Camera RAW output Output unformatted command to the camera. PTZ head – PTZ head. output – RAW command to output. 5.4 Camera apply profile Apply a predefined profile settings to the camera. PTZ head – PTZ head. profile – Profile name. 5.5 Camera backlight compensation mode Change backlight compensation mode of the camera. PTZ head – PTZ head. mode – Backlight compensation mode. 26 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 26 --- GEUTEBRUCK5.6 Camera clear preset text Clear camera text for preset position. PTZ head – PTZ head. position – Preset position. 5.7 Camera day/night mode Change day/night mode of the camera. PTZ head – PTZ head. mode – Day/night mode. 5.8 Camera light off Turn camera light off. PTZ head – PTZ head. 5.9 Camera light on Turn camera light on. PTZ head – PTZ head. 5.10 Camera manual iris off Disable manual iris of the camera. PTZ head – PTZ head. 5.11 Camera manual iris on Enable manual iris of the camera. PTZ head – PTZ head. 5.12 Camera off Turn camera off. PTZ head – PTZ head. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 27 --- Page 27 --- GEUTEBRUCK5.13 Camera on Turn camera on. PTZ head – PTZ head. 5.14 Camera pump off Turn camera pump off. PTZ head – PTZ head. 5.15 Camera pump on Turn camera pump on. PTZ head – PTZ head. 5.16 Camera select char mode Select camera character mode. PTZ head – PTZ head. mode – Character mode. 5.17 Camera set preset text Set camera text for preset position. PTZ head – PTZ head. position – Preset position. 5.18 Camera spec func U off Turn camera special function U off. PTZ head – PTZ head. 5.19 Camera spec func U on Turn camera special function U on. PTZ head – PTZ head. 28 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 28 --- GEUTEBRUCK5.20 Camera spec func V off Turn camera special function V off. PTZ head – PTZ head. 5.21 Camera spec func V on Turn camera special function V on. PTZ head – PTZ head. 5.22 Camera spec func X off Turn camera special function X off. PTZ head – PTZ head. 5.23 Camera spec func X on Turn camera special function X on. PTZ head – PTZ head. 5.24 Camera spec func Y off Turn camera special function Y off. PTZ head – PTZ head. 5.25 Camera spec func Y on Turn camera special function Y on. PTZ head – PTZ head. 5.26 Camera stop all Camera stop all. PTZ head – PTZ head. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 29 --- Page 29 --- GEUTEBRUCK5.27 Camera text off Disable camera text. PTZ head – PTZ head. 5.28 Camera text on Enable camera text. PTZ head – PTZ head. 5.29 Camera tour start Start camera tour. PTZ head – PTZ head. tour ID – Tour ID. tour name – Tour name. 5.30 Camera tour stop Stop camera tour. PTZ head – PTZ head. 5.31 Camera version off Hide camera version string. PTZ head – PTZ head. 5.32 Camera version on Show camera version string. PTZ head – PTZ head. 5.33 Camera wash-wipe off Turn camera wash-wipe off. PTZ head – PTZ head. 30 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 30 --- GEUTEBRUCK5.34 Camera wash-wipe on Turn camera wash-wipe on. PTZ head – PTZ head. 5.35 Clear default position Clear camera default position. PTZ head – PTZ head. 5.36 Clear preset position Clear camera preset position. PTZ head – PTZ head. position – Preset position. 5.37 Fast speed off Turn camera fast speed off. PTZ head – PTZ head. 5.38 Fast speed on Turn camera fast speed on. PTZ head – PTZ head. 5.39 Focus far Focus camera far. PTZ head – PTZ head. speed – Focus speed. 5.40 Focus near Focus camera near. PTZ head – PTZ head. speed – Focus speed. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 31 --- Page 31 --- GEUTEBRUCK5.41 Focus stop Stop camera focus. PTZ head – PTZ head. 5.42 Iris close Close camera iris. PTZ head – PTZ head. 5.43 Iris open Open camera iris. PTZ head – PTZ head. 5.44 Iris stop Stop camera iris. PTZ head – PTZ head. 5.45 Move by speed Move camera by speed. PTZ head – PTZ head. alpha speed – Speed in alpha (pan) direction (0/100 %). beta speed – Speed in beta (tilt) direction (0/100 %). 5.46 Move to absolute position Move camera to absolute position. PTZ head – PTZ head. alpha – Alpha angle (-180/+180). beta – Beta angle (-90/+90). alpha speed – Speed in alpha direction (0/100 %). beta speed – Speed in beta direction (0/100 %). 32 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 32 --- GEUTEBRUCK5.47 Move to default position Move camera to default position. PTZ head – PTZ head. 5.48 Move to preset position Move camera to preset position. PTZ head – PTZ head. position – Preset position. 5.49 Move to relative position Move camera to relative position. PTZ head – PTZ head. alpha – Alpha angle (-180/+180). beta – Beta angle (-90/+90). alpha speed – Speed in alpha direction (0/100 %). beta speed – Speed in beta direction (0/100 %). 5.50 Pan auto Turn auto pan of the camera. PTZ head – PTZ head. modus – Pan modus. 5.51 Pan left Pan camera to the left. PTZ head – PTZ head. speed – Pan speed. 5.52 Pan right Pan camera to the right. PTZ head – PTZ head. speed – Pan speed. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 33 --- Page 33 --- GEUTEBRUCK5.53 Pan stop Stop pan movement. PTZ head – PTZ head. 5.54 Save default position Save current camera position as default position. PTZ head – PTZ head. 5.55 Save preset position Save current camera position as preset position. PTZ head – PTZ head. position – Preset position. 5.56 Set camera text Set camera text. PTZ head – PTZ head. text – Text to superimpose. 5.57 Tilt down Tilt camera down. PTZ head – PTZ head. speed – Tilt speed. 5.58 Tilt stop Stop tilt movement. PTZ head – PTZ head. 34 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 34 --- GEUTEBRUCK5.59 Tilt up Tilt camera up. PTZ head – PTZ head. speed – Tilt speed. 5.60 Zoom in Zoom camera in. PTZ head – PTZ head. speed – Zoom speed. 5.61 Zoom out Zoom camera out. PTZ head – PTZ head. speed – Zoom speed. 5.62 Zoom stop Stop camera zoom. PTZ head – PTZ head. 6 Cash management actions All actions for cash management. 6.1 Safebag close Safebag close. working place – Working place no. start time – Start time stamp. stop time – Stop time stamp. safebag no. – Safebag no. safebag info – Additional info about safebag. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 35 --- Page 35 --- GEUTEBRUCKstep ID – Processing step ID. debit – Debit. total – Total. difference – Difference between debit and total. has difference – Difference between debit and total is not zero. notes – Notes. coins – Coins. cheques – Cheques. 6.2 Safebag data Safebag data. working place – Working place no. start time – Start time stamp. safebag no. – Safebag no. safebag info – Additional info about safebag. step ID – Processing step ID. debit – Debit. total – Total. difference – Difference between debit and total. has difference – Difference between debit and total is not zero. notes – Notes. coins – Coins. cheques – Cheques. 6.3 Safebag open Safebag open. working place – Working place no. start time – Start time stamp. safebag no. – Safebag no. safebag info – Additional info about safebag. step ID – Processing step ID. 36 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 36 --- GEUTEBRUCK6.4 Safebag passing of risk data Safebag passing of risk data. working place – Working place no. start time – Start time stamp. safebag no. – Safebag no. safebag info – Additional info about safebag. step ID – Processing step ID. user 1 – User who gives the safebag. user 2 – User who takes the safebag. tour no – Optional tour no. target working place – Target working place. passing of risk type – Passing of risk type. 6.5 Safebag passing of risk start Safebag passing of risk start. working place – Working place no. start time – Start time stamp. safebag no. – Safebag no. safebag info – Additional info about safebag. step ID – Processing step ID. user 1 – User who gives the safebag. user 2 – User who takes the safebag. tour no – Optional tour no. target working place – Target working place. passing of risk type – Passing of risk type. 6.6 Safebag passing of risk stop Safebag passing of risk stop. working place – Working place no. start time – Start time stamp. stop time – Stop time stamp. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 37 --- Page 37 --- GEUTEBRUCKsafebag no. – Safebag no. safebag info – Additional info about safebag. step ID – Processing step ID. user 1 – User who gives the safebag. user 2 – User who takes the safebag. tour no – Optional tour no. target working place – Target working place. passing of risk type – Passing of risk type. 7 Device information All actions for low-level notification of the device or media channels changes. 7.1 Device found This action will be fired when the USB or NET device is connected to the system. It is also fired at start-up for all detected devices. device type – Type of the device. device name – Device name if assigned in setup, empty otherwise. serial ID – Serial ID of the device. 7.2 Device plugin error This action notifies device plugin error. channel – Channel. device type – Type of the device. device subtype – Subtype of the device. device name – Device name. serial ID – Serial ID of the device. error class – Error class of the error occured. error code – Plugin type specific error code. description – Error description. 38 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 38 --- GEUTEBRUCK7.3 Device plugin state This action notifies device plugin state. channel – Channel. device type – Type of the device. device subtype – Subtype of the device. device name – Device name. serial ID – Serial ID of the device. plugin state – New plugin device state. internal state – Plugin device specific state. description – State description. 7.4 Device reattached This action will be fired when the USB or NET device is reattached to the system. device type – Type of the device. device name – Device name if assigned in setup, empty otherwise. serial ID – Serial ID of the device. 7.5 Device removed This action will be fired when the USB or NET device is disconnected from the system. It is also fired at the start-up for all parameterized but not present devices. device type – Type of the device. device name – Device name if assigned in setup, empty otherwise. serial ID – Serial ID of the device. 7.6 New firmware received This action will be fired when the USB or NET device has got the new firmware. device type – Type of the device. device name – Device name if assigned in setup, empty otherwise. serial ID – Serial ID of the device. firmware serial – Serial ID of the firmware. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 39 --- Page 39 --- GEUTEBRUCK8 Digital contacts All actions for handling digital inputs and outputs. 8.1 Case has been closed Case has been closed. This action has no parameters. 8.2 Case has been opened Case has been opened. This action has no parameters. 8.3 Digital input This action will be fired when the state of the digital input has changed. contact – Contact. state – New state. 8.4 IOI43 reset mainboard Reset mainboard using IOI43a/ab USB Alarm-I/O. This action has no parameters. 8.5 IOI43 temperature notification Temperature notification from IOI43a/ab USB Alarm-I/O. ID – ID of the IOI43 module (like IOI43-00). temperature – Temperature. 8.6 IOI43 watchdog activate Activate watchdog on IOI43a/ab USB Alarm-I/O. This action has no parameters. 40 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 40 --- GEUTEBRUCK8.7 IOI43 watchdog deactivate Deactivate watchdog on IOI43a/ab USB Alarm-I/O. This action has no parameters. 8.8 IOI43 watchdog trigger Trigger watchdog on IOI43a/ab USB Alarm-I/O. This action has no parameters. 8.9 Key pressed This action is notified if one of the GEVISCOPE system keys is pressed. key – System key. 8.10 Key released This action is notified if one of the GEVISCOPE system keys is released. key – System key. 8.11 Reset mainboard Reset mainboard using IO device. This action has no parameters. 8.12 Set digital output This action is used to modify the state of the digital output and to notify this change. contact – Contact. state – New state. 8.13 Set system LED This action is used to turn the system LEDs on or off. LED – System LED. state – New state. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 41 --- Page 41 --- GEUTEBRUCK8.14 Set system LED to blink This action is used to blink the system LEDs. LED – System LED. LED time ON – Time in milliseconds when the LED will be switched on. LED time OFF – Time in milliseconds when the LED will be switched off. 8.15 Temperature notification Temperature notification from a/ab USB Alarm-I/O. IO device type – Type of the device, which has fired the action. ID – ID of the IO module (like IOI43-00/MIO84-00/MIO168-00). temperature – Temperature. 8.16 Watchdog activate Activate watchdog. This action has no parameters. 8.17 Watchdog deactivate Deactivate watchdog. This action has no parameters. 8.18 Watchdog trigger Trigger watchdog. This action has no parameters. 9 Imex Image export. 42 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 42 --- GEUTEBRUCK9.1 Imex capacity file auto deleted Imex capacity warning: file auto deleted. warning – Warning. destination – Destination. total capacity – Total capacity. free capacity – Free capacity. allocated by image file – Allocated by image file. percent free – Percent free. percent allocated – Percent allocated. percent allocated by image file – Percent allocated by image file. total file size – Total file size. number of files – Number of files. 9.2 Imex capacity out of disk space. Imex capacity warning: out of disk space. warning – Warning. destination – Destination. total capacity – Total capacity. free capacity – Free capacity. allocated by image file – Allocated by image file. percent free – Percent free. percent allocated – Percent allocated. percent allocated by image file – Percent allocated by image file. 9.3 Imex capacity warning Imex capacity warning: capacity warning. warning – Warning. destination – Destination. total capacity – Total capacity. free capacity – Free capacity. allocated by image file – Allocated by image file. percent free – Percent free. percent allocated – Percent allocated. percent allocated by image file – Percent allocated by image file. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 43 --- Page 43 --- GEUTEBRUCK9.4 Imex export event image Imex export event image. instance ID – Instance ID of the event. event type – Type of the event. destination – Destination. file name – File name. 9.5 Imex export image from DB Imex export image from DB. channel – Channel. destination – Destination. file name – File name. picture time – Picture time. 9.6 Imex export image from live stream Imex export image from live stream. channel – Channel. destination – Destination. file name – File name. 10 LPS LPS messages. 10.1 LPS position data LPS position data. tag ID – Tag ID. scanner ID – Scanner ID or IP address. X coordinate – X coordinate of cartesian coordinates. Y coordinate – Y coordinate of cartesian coordinates. 44 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 44 --- GEUTEBRUCKZ coordinate – Z coordinate of cartesian coordinates. latitude – Latitude of geographic coordinates. longitude – Longitude of geographic coordinates. area ID – Area ID. cell ID – Cell ID. status – Status. time stamp – Time stamp. data – Data. area name – Area Name. 10.2 LPS query position Send position query for a Tag to LPS server. tag ID – Tag ID. scanner ID – Scanner ID or IP address. data – Data. 11 Lenel Lenel. 11.1 Lenel access event Lenel OnGuard access event. ID – The ID that uniquely identifies the type of this event. panel – The name of the panel where this event originated. device – The name of the device where this event originated. secondary device – The ID of the secondary device where this event origi- nated. card number – The badge ID for the card that was read, if available. access result – The level of access that was granted that resulted from read- ing the card. type – Event type i.e., duress, system, etc. subtype – Event sub-type i.e., granted, door forced open, etc. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 45 --- Page 45 --- GEUTEBRUCKdescription – A human readable, brief description of this event. serial number – A number that uniquely identifies the instance of the event for a particular panel. time stamp – Time stamp. area entered – The ID of the area that was entered, if any. area exited – The ID of the area that was exited, if any. asset ID – The ID of the asset related to this event, if any. cardholder entered – Whether entry was made by the cardholder. duress – Indicates whether this card access indicates an under duress/emergency state. elevator floor – The elevator floor on which the access event was generated, if any. facility code – The facility code for the card that was read, if available. readable card – Whether the card could be read. issue code – The issue code for the card that was read, if available. server host – Host name of the Communication server through which the event arrived. event text – Text associated with event 11.2 Lenel fire event Lenel OnGuard fire event. ID – The ID that uniquely identifies the type of this event. panel – The name of the panel where this event originated. device – The name of the device where this event originated. secondary device – The ID of the secondary device where this event origi- nated. trouble code – A trouble code associated with the fire event. type – Event type i.e., duress, system, etc. subtype – Event sub-type i.e., granted, door forced open, etc. description – A human readable, brief description of this event. serial number – A number that uniquely identifies the instance of the event for a particular panel. time stamp – Time stamp. server host – Host name of the Communication server through which the event arrived. event text – Text associated with event 46 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 46 --- GEUTEBRUCK11.3 Lenel intercom event Lenel OnGuard intercom event. ID – The ID that uniquely identifies the type of this event. panel – The name of the panel where this event originated. device – The name of the device where this event originated. secondary device – The ID of the secondary device where this event origi- nated. intercom data – Additional data for the intercom event that occurred. line number – The line number involved in the intercom event. type – Event type i.e., duress, system, etc. subtype – Event sub-type i.e., granted, door forced open, etc. description – A human readable, brief description of this event. serial number – A number that uniquely identifies the instance of the event for a particular panel. time stamp – Time stamp. server host – Host name of the Communication server through which the event arrived. event text – Text associated with event 11.4 Lenel raw data Lenel OnGuard raw data. time stamp – Time stamp. data – Lenel OnGuard data. 11.5 Lenel refresh names Lenel OnGuard refresh names. This action has no parameters. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 47 --- Page 47 --- GEUTEBRUCK11.6 Lenel security event Lenel OnGuard security event. ID – The ID that uniquely identifies the type of this event. panel – The name of the panel where this event originated. device – The name of the device where this event originated. secondary device – The ID of the secondary device where this event origi- nated. type – Event type i.e., duress, system, etc. subtype – Event sub-type i.e., granted, door forced open, etc. description – A human readable, brief description of this event. serial number – A number that uniquely identifies the instance of the event for a particular panel. time stamp – Time stamp. server host – Host name of the Communication server through which the event arrived. event text – Text associated with event 11.7 Lenel video event Lenel OnGuard video event. ID – The ID that uniquely identifies the type of this event. panel – The name of the panel where this event originated. device – The name of the device where this event originated. secondary device – The ID of the secondary device where this event origi- nated. channel – The physical channel the camera is connected to that is creating this event. type – Event type i.e., duress, system, etc. subtype – Event sub-type i.e., granted, door forced open, etc. description – A human readable, brief description of this event. serial number – A number that uniquely identifies the instance of the event for a particular panel. time stamp – Time stamp. start stamp – The time the video event started end time – The time the video event ended. server host – Host name of the Communication server through which the event arrived. event text – Text associated with event 48 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 48 --- GEUTEBRUCK12 POS POS (point of sale). 12.1 Barcode data Barcode data. scanner – Scanner name. time stamp – Time stamp. code – Barcode. 12.2 Filling pump status Filling pump status. terminal – Terminal name. time stamp – Time stamp. pump no – Pump no. status – Status. amount – Amount. price – Price. details – Details. 12.3 Interface raw answer Interface raw answer. interface – Interface name. time stamp – Time stamp. answer – Interface answer. 12.4 Interface raw data Interface raw data. interface – Interface name. time stamp – Time stamp. data – Interface data. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 49 --- Page 49 --- GEUTEBRUCK12.5 POS data POS data. POS – POS name. time stamp – Time stamp. article – Article description. price – Price. units – Number of units. price per unit – Price per unit. line 1 – Line 1. line 2 – Line 2. line 3 – Line 3. line 4 – Line 4. line 5 – Line 5. 12.6 POS status POS status. POS – POS name. time stamp – Time stamp. status – Status. details – Details. 12.7 Terminal article data Terminal article data. terminal – Terminal name. time stamp – Time stamp. cashier station – Cashier station. pump no – Pump no. alarm – Alarm status. amount – Amount. price – Price. details – Details. 50 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 50 --- GEUTEBRUCK12.8 Terminal payment data Terminal payment data. terminal – Terminal name. time stamp – Time stamp. cashier station – Cashier station. pump no – Pump no. alarm – Alarm status. amount – Amount. price – Price. details – Details. 13 Perimeter protection Perimeter protection. 13.1 PP device alarm Perimeter protection device alarm. interface id – Interface ID. device address – Device address. sensor – Sensor. state – State. 13.2 PP device input Perimeter protection device input. interface id – Interface ID. device address – Device address. input – Input. state – State. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 51 --- Page 51 --- GEUTEBRUCK13.3 PP device offline Perimeter protection device offline. interface id – Interface ID. device address – Device address. 13.4 PP device online Perimeter protection device online. interface id – Interface ID. device address – Device address. 13.5 PP interface offline Perimeter protection interface offline. interface id – Interface ID. 13.6 PP interface online Perimeter protection interface online. interface id – Interface ID. 13.7 PP query interface Perimeter protection query interface. interface id – Interface ID. 13.8 PP set device output Perimeter protection set device output. interface id – Interface ID. device address – Device address. output – Output. state – State. 52 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 52 --- GEUTEBRUCK13.9 PP subcell alarm Perimeter protection subcell alarm. interface id – Interface ID. device address – Device address. cable – Cable. subcell – Subcell. state – State. 13.10 PP zone alarm Perimeter protection zone alarm. zone id – Zone ID. interface id – Interface ID. device address – Device address. cable – Cable. subcell – Subcell. state – State. 14 Remote export Remote export. 14.1 Cancel export Cancel export. export GUID – Export GUID. abort flag – Abort flag. 14.2 Export finished Export finished. export GUID – Export GUID. success – Success. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 53 --- Page 53 --- GEUTEBRUCK14.3 Export progress Export progress. export GUID – Export GUID. progress – Progress. 14.4 Initialize remote export Initialize remote export. viewer – Global viewer or viewer client no. device GUID – Pilot device GUID. 14.5 Set export marker Set export marker. viewer – Global viewer or viewer client no. marker – Marker kind. 14.6 Start remote export Start remote export. export GUID – Export GUID. device GUID – Pilot device GUID. format – Backup format. channel – Channel. start time – Start time. end time – End time. job ID – Job ID. 14.7 Start scene store Start scene store. scene store GUID – Scene store GUID. cut-list – Cut-list. pre-history length – Pre-history length. recording length – Recording length. 54 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 54 --- GEUTEBRUCK15 SKIDATA SKIDATA messages. 15.1 SKIDATA control SKIDATA control information. interface – Interface name. state – Interface state. 15.2 SKIDATA device event SKIDATA device event. interface – Interface name. device – Device ID. event code – Event code. 15.3 SKIDATA entry SKIDATA entry. interface – Interface name. message – Message code. transaction – Transcaction ID. car park – Car park no. device – Device ID. 15.4 SKIDATA exit SKIDATA exit. interface – Interface name. message – Message code. transaction – Transcaction ID. car park – Car park no. device – Device ID. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 55 --- Page 55 --- GEUTEBRUCK15.5 SKIDATA transaction SKIDATA transaction. interface – Interface name. message – Message code. transaction – Transcaction ID. car park – Car park no. device – Device ID. 16 Supply chain security Supply chain security. 16.1 GSCS vehicle access denied GSCS vehicle access denied. sequence ID – The sequence ID. plate no. – Recognized plate no. time stamp – Time stamp. company category – Company category. company name – Company name. reason – Reason. traffic lane – Traffic lane. channel – Channel. direction – Direction. 16.2 GSCS vehicle access expired GSCS vehicle access expired. sequence ID – The sequence ID. plate no. – Recognized plate no. time stamp – Time stamp. expiring time – Expiring time. company category – Company category. 56 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 56 --- GEUTEBRUCKcompany name – Company name. reason – Reason. traffic lane – Traffic lane. channel – Channel. direction – Direction. 16.3 GSCS vehicle access granted GSCS vehicle access granted. sequence ID – The sequence ID. plate no. – Recognized plate no. time stamp – Time stamp. company category – Company category. company name – Company name. reason – Reason. traffic lane – Traffic lane. channel – Channel. direction – Direction. 16.4 GSCS vehicle access pending GSCS vehicle access pending. sequence ID – The sequence ID. plate no. – Recognized plate no. time stamp – Time stamp. company category – Company category. company name – Company name. reason – Reason. traffic lane – Traffic lane. channel – Channel. direction – Direction. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 57 --- Page 57 --- GEUTEBRUCK16.5 Log NPR recognition Log NPR recognition. plate no. – Recognized plate no. hash value – Hash value. country – Country. channel – Channel. time stamp – Time stamp. restriction – Restriction of recognized number. category – Category of recognized number. 16.6 Log barcode data Logistic barcode data. barcode – Barcode. hash value – Hash value. scanner name – Scanner name or IP address. area number – Area number. area name – Area name. channel – Channel. time stamp – Time stamp. order number – Order number. shipment number – Shipment number. item number – Item number. 16.7 Log barcode data LPS Logistic barcode and LPS data. barcode – Barcode. hash value – Hash value. scanner name – Scanner name or IP address. area number – Area number. area name – Area name. channel – Channel. 58 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 58 --- GEUTEBRUCKtime stamp – Time stamp. X coordinate – X coordinate. Y coordinate – Y coordinate. Z coordinate – Z coordinate. LPS tag ID – LPS tag ID. LPS status – LPS status. LPS cell ID – LPS cell ID. LPS area ID – LPS area ID. user param – User param. order number – Order number. shipment number – Shipment number. item number – Item number. 17 System actions All actions describing system behaviour. 17.1 Blocking filter activate Blocking filter activate. filter – Blocking filter. 17.2 Blocking filter deactivate Blocking filter deactivate. filter – Blocking filter. 17.3 Custom action This action has no side effects and can be used for customer purposes. INT parameter – Numeric parameter. STRING parameter – Literal parameter. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 59 --- Page 59 --- GEUTEBRUCK17.4 Database recording info per ring Database recording info per ring. database ring – Database ring. no video recording – Video is recording or not. no audio recording – Audio is recording or not. no recording – Video and/or audio is recording or not. video samples/s – Video samples per second. video samples MB/s – Video MB per second. audio samples/s – Audio samples per second. audio samples MB/s – Audio MB per second. write wait % – Write waiting times in percent. ring capacity – Ring capacity. oldest item – Time stamp of the oldest item. recording depth – Recording depth in hours. estimated required capacity – Estimated required capacity. 17.5 Database recording info total Database recording info total. no video recording – Video is recording or not. no audio recording – Audio is recording or not. no recording – Video and/or audio is recording or not. video samples/s – Video samples per second. video samples MB/s – Video MB per second. audio samples/s – Audio samples per second. audio samples MB/s – Audio MB per second. write wait % – Write waiting times in percent. total capacity – Total capacity. free capacity – Free capacity. allocated capacity – Allocated capacity. oldest item – Time stamp of the oldest item. recording depth – Recording depth in hours. estimated required capacity – Estimated required capacity. required capacity factor – Required capacity factor. required capacity available – Required capacity available. 60 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 60 --- GEUTEBRUCK17.6 Database started This action will be fired at the database start-up. status – Database status message. total size – Database total size. 17.7 Event recording changed Event recording settings are changed. instance ID – Instance ID of the event. event type – Type of the event. 17.8 Event started Event has started. instance ID – Instance ID of the event. event type – Type of the event. foreign key – Optional foreign key used to start the alarm. 17.9 Event stopped Event has stopped. instance ID – Instance ID of the event. event type – Type of the event. 17.10 FRC notification FRC notification. notification – Notification reason. param – Additional parameter. description – Optional notification text. additional info – Optional additional info (usually as XML string). GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 61 --- Page 61 --- GEUTEBRUCK17.11 GEMOS alarm GEMOS alarm notification. GEMOS key – GEMOS alarm key. GEMOS int – GEMOS alarm integer parameter. GEMOS str – GEMOS alarm string parameter. 17.12 IP switch operation IP switch operation. operation – Operation. port no – Port no, IP address, MAC address. parameter – Optional parameter. 17.13 Kill all events Kill all active events. This action has no parameters. 17.14 Kill event Kill event. event type – Type of the event. 17.15 Kill event by instance Kill event by instance ID. instance ID – Instance ID of the event. 17.16 Live check This action will be fired every 10 seconds and is intended for use as live check. counter – This is the number of already fired live check actions. time stamp – Current server time. 62 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 62 --- GEUTEBRUCK17.17 Redundant power failure This action is notified if a failure of the redundant power supply is detected. This action has no parameters. 17.18 Redundant power ok This action is notified if a failure of the redundant power supply is removed. This action has no parameters. 17.19 SMRP viewer cleared SMRP viewer cleared. This action has no parameters. 17.20 SMRP viewer connected SMRP viewer connected to the camera. server – Server name. channel – Channel. 17.21 SMTP mail This action will send a user defined email if GSCMail is connected subject – Mail subject. to –Mail recipients. cc – Carbon copy recipients. body – Mail body. channel – Channel. 17.22 Set clock Set clock. current time – Current time. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 63 --- Page 63 --- GEUTEBRUCK17.23 Set watchdog Set watchdog. timeout – Timeout in seconds, before the watchdog must be retriggered and before the hardware watchdog will set the hardware contact. 17.24 Setup changed Setup changed. user name – Name of the user who modified the setup. remote host – Host from where the connection was done. current time – Current time. resource kind – Modified resource kind. resource ID – Modified resource ID. change kind – Change kind. details – Details of the modification. client host – Host from where the connection is done. client type – Client type. client account – User account from where the connection is done. 17.25 Setup upload progress Setup upload progress. first user – Name of the user who modified the setup. second user – Name of the second user by four eyes authentication. remote host – Host from where the connection was done. progress % – Progress in percent. current time – Current stage time. 17.26 Start event Start event. event type – Type of the event. foreign key – Optional foreign key used to store with alarm. 64 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 64 --- GEUTEBRUCK17.27 Stop all events Stop all active events. This action has no parameters. 17.28 Stop event Stop event. event type – Type of the event. 17.29 Stop event by instance Stop event by instance ID. instance ID – Instance ID of the event. 17.30 System error Notify system error. source subsystem – Source of the message. message code – Kind of the message. Windows error code – Optional Windows error code. description – Optional description of the message. additional info – Optional additional info (usually as XML string). 17.31 System info Notify system information. source subsystem – Source of the message. message code – Kind of the message. description – Optional description of the message. additional info – Optional additional info (usually as XML string). GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 65 --- Page 65 --- GEUTEBRUCK17.32 System settings changed Setup of the system and/or the current time range changed. setup changed – System setup has changed. first user – Name of the user who modified the setup. second user – Name of the second user by four eyes authentication. remote host – Host from where the connection was done. time range changed – Time range has changed. current time range – Currently active time range. licence changed – Licence has changed. change time – Time of the system settings changed. 17.33 System started This action will be fired only once at the system start-up. start time – Time of the system start-up. 17.34 System terminating This action will be fired when the system is going to be shut down. stop time – Time of the system shutdown. Windows shutdown – Indicates whether the system shutdown is done due to the windows shutdown. 17.35 System warning Notify system warning. source subsystem – Source of the message. message code – Kind of the message. Windows error code – Optional Windows error code. description – Optional description of the message. additional info – Optional additional info (usually as XML string). 66 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 66 --- GEUTEBRUCK17.36 Transfer binary buffer Transfer binary buffer. internal handle – Internal handle. parameter – Parameter. 17.37 Transfer binary channel buffer Transfer binary channel buffer. channel – Channel. internal handle – Internal handle. parameter – Parameter. 17.38 User login This action will be fired when the user has connected to the system. first user – Name of the user connected to the system. second user – Name of the second user by four eyes authentication. remote host – Host from where the connection is done. client host – Host from where the connection is done. client type – Client type. client account – User account from where the connection is done. 17.39 User login failed This action will be fired when the user has tried to connect to the system but was rejected. first user – Name of the user who tried to connect to the system. second user – Name of the second user by four eyes authentication. remote host – Host from where the connection is done. reject reason – Reason of the rejection. client host – Host from where the connection is done. client type – Client type. client account – User account from where the connection is done. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 67 --- Page 67 --- GEUTEBRUCK17.40 User logout This action will be fired when the user has disconnected from the system. first user – Name of the user disconnected from the system. second user – Name of the second user by four eyes authentication. remote host – Host from where the connection was done. client host – Host from where the connection is done. client type – Client type. client account – User account from where the connection is done. 18 Video control All actions to control the video streams, also all notifications about the state change of the video streams. 18.1 Activate external process Activate external process. channel – Channel. time stamp – Time stamp. external system – External system to activate. 18.2 CPA measurement CPA measurement. channel – Channel. correlation – Correlation factor. 18.3 Change AD parameter set This action changes the current AD parameter set of the video channel. channel – Channel. AD parameter set – The name of the new AD parameter set. 68 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 68 --- GEUTEBRUCK18.4 Change CPA parameter set This action changes the current CPA parameter set of the video channel. channel – Channel. CPA parameter set – The name of the new CPA parameter set. 18.5 Change GTectVMX parameter set This action changes the current GTectVMX parameter set of the video channel. channel – Channel. GTect parameter set – The name of the new GTect parameter set. 18.6 Change OBTRACK parameter set This action changes the current OBTRACK parameter set of the video channel. channel – Channel. OBTRACK parameter set – The name of the new OBTRACK parameter set. 18.7 Change VMD parameter set This action changes the current VMD parameter set of the video channel. channel – Channel. VMD parameter set – The name of the new VMD parameter set. 18.8 Change camera profile This action changes the current camera profile of the hardware module. hardware – Hardware module. profile – The name of the camera profile. 18.9 Channel error Notify channel error. channel – Channel. sensor type – Sensor type. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 69 --- Page 69 --- GEUTEBRUCKsource subsystem – Source of the message. message code – Kind of the message. Windows error code – Optional Windows error code. description – Optional description of the message. additional info – Optional additional info (usually as XML string). 18.10 Channel info Notify channel information. channel – Channel. sensor type – Sensor type. source subsystem – Source of the message. message code – Kind of the message. description – Optional description of the message. additional info – Optional additional info (usually as XML string). 18.11 Channel live check This action notifies that the channel is alive. channel – Channel. sensor type – Sensor type. time stamp – Time stamp. 18.12 Channel warning Notify channel warning. channel – Channel. sensor type – Sensor type. source subsystem – Source of the message. message code – Kind of the message. Windows error code – Optional Windows error code. description – Optional description of the message. additional info – Optional additional info (usually as XML string). 70 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 70 --- GEUTEBRUCK18.13 Enable client VCA Enable client VCA channel – Channel. VCA Type – VCA Type enabled – Enabled 18.14 G-Tect analytics live check This action will be fired periodically to ensure that analytics client is still running. This action has no parameters. 18.15 G-Tect scene alarm This action will be fired when G-Tect Video content analysis detects a scene alarm. channel – Channel. alarm reason – Alarm reason. 18.16 G-Tect scene alarm finished This action will be fired when G-Tect Video content analysis scene alarm is fin- ished. channel – Channel. alarm reason – Alarm reason. 18.17 G-Tect/Dual sensor alarm This action will be fired when G-Tect/Dual sensor detects an alarm. channel – Channel. sterile zone number – Sterile Zone Number virtual fence number – Virtual Fence Number. VMD alarm group – VMD alarm group. VMD zone – VMD zone nr. VMD cycle – VMD measure cycle. alarm area – Alarm area. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 71 --- Page 71 --- GEUTEBRUCK18.18 G-Tect/Dual sensor alarm finished This action will be fired when the alarm is finished. channel – Channel. 18.19 G-Tect/VMX alarm This action will be fired when G-Tect/VMX Video content analysis detects an alarm. channel – Channel. sterile zone number – Sterile Zone Number virtual fence number – Virtual Fence Number. group zones or fences – Used to group different Zones or fences to the same level. internal track ID – Internal Track ID. alarm area – Alarm area. 18.20 G-Tect/VMX alarm finished This action will be fired when the alarm is finished. channel – Channel. 18.21 IAS settings changed IAS settings changed. channel – Channel. sensor type – Sensor type. 18.22 IP camera failover notification IP camera failover notification. primary server – The name of the primary server. secondary server – The name of the secondary server. primary channel – Primary channel. secondary channel – Secondary channel. camera parameters – Optional camera parameters. 72 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 72 --- GEUTEBRUCK18.23 IP camera failover restore IP camera failover restore. primary server – The name of the primary server. secondary server – The name of the secondary server. primary channel – Primary channel. secondary channel – Secondary channel. camera parameters – Optional camera parameters. 18.24 IP camera raw command This action sends a special command to the IP camera. url – Complete command URL (like http://192.168.0.165:80/set?daynight=night). user – User name to authenticate by the camera (optional). password – Password to authenticate by the camera (optional). post – POST parameters (optional, separate lines with r n). 18.25 Make CPA reference image Make CPA reference image. channel – Channel. 18.26 Media channel setup Media channel setup info. channel – Channel. time stamp – Time stamp. parameter – Parameter. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 73 --- Page 73 --- GEUTEBRUCK18.27 NPR raw data NPR raw data. plate no. – Recognized plate no. country – Country. channel – Channel. time stamp – Time stamp. zone rect – Zone rectangle. weight – Weight of recognition. zone state – Zone state. zone status – Zone status. speed – Speed in km/h direction – Direction of the motion. zone index – Zone index. best – Current recognition is best. plate width – Plate width. plate height – Plate height. plate angle – Plate angle. symbol height – Symbol height. type – Number type. 18.28 NPR recognition NPR recognition. plate no. – Recognized plate no. country – Country. channel – Channel. time stamp – Time stamp. zone rect – Zone rectangle. restriction – Restriction of recognized number. category – Category of recognized number. speed – Speed in km/h direction – Direction of the motion. zone index – Zone index. type – Number type. weight – Weight of recognition. 74 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 74 --- GEUTEBRUCK18.29 OBTRACK channel counter OBTRACK channel counter. channel – Channel. counter type – Counter type. counter value – Counter value. object direction – Object direction. time stamp – Time stamp. reset time stamp – Reset time stamp. 18.30 OBTRACK channel counter threshold OBTRACK channel counter threshold. channel – Channel. counter type – Counter type. counter value – Counter value. exceeding direction – Exceeding direction. time stamp – Time stamp. 18.31 OBTRACK channel set counter OBTRACK channel set counter. channel – Channel. counter type – Counter type. counter value – Counter value. time stamp – Time stamp. 18.32 OBTRACK frame raw data OBTRACK frame raw data. time stamp – Time stamp. channel – Channel. brightness – Brightness. contrast – Contrast. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 75 --- Page 75 --- GEUTEBRUCK18.33 OBTRACK group counter OBTRACK group counter. group ID – Group ID. counter type – Counter type. counter value – Counter value. object direction – Object direction. time stamp – Time stamp. reset time stamp – Reset time stamp. group name – Group name. 18.34 OBTRACK group counter threshold OBTRACK group counter threshold. group ID – Group ID. counter type – Counter type. counter value – Counter value. exceeding direction – Exceeding direction. time stamp – Time stamp. group name – Group name. 18.35 OBTRACK group set counter OBTRACK group set counter. group ID – Group ID. counter type – Counter type. counter value – Counter value. time stamp – Time stamp. group name – Group name. 76 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 76 --- GEUTEBRUCK18.36 OBTRACK object raw data OBTRACK object raw data. time stamp – Time stamp. channel – Channel. area no – Area no. object ID – Object ID. object status – Object status. object class – Object class. confidence – Confidence. position – Position. speed – Speed. duration – Duration. direction – Direction. object size – Object size. object width – Object width in meters. object height – Object height in meters. process size – Process size. GSC net name – GeViScope network name. 18.37 OBTRACK tunnel alarm OBTRACK tunnel alarm notification. channel – Channel. time stamp – Time stamp. alarm reason – Alarm reason. object ID – Object ID. alarm area ID – Alarm area ID. object area – Object area. 18.38 Sensor alarm finished This action will be fired when the alarm is finished. channel – Channel. sensor type – Sensor type. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 77 --- Page 77 --- GEUTEBRUCK18.39 Sensor inhibit alarm finished This action will be fired when the inhibit alarm is finished. channel – Channel. sensor type – Sensor type. 18.40 Sensor inhibit video alarm This action will be fired when the motion in inhibit area is detected. channel – Channel. sensor type – Sensor type. AD alarm area – AD alarm area. AD cell – AD cell nr. VMD alarm group – VMD alarm group. VMD zone – VMD zone nr. VMD cycle – VMD measure cycle. alarm area – Alarm area. object class – OBTRACK object class. 18.41 Sensor video alarm This action will be fired when video alarm is detected. channel – Channel. sensor type – Sensor type. AD alarm area – AD alarm area. AD cell – AD cell nr. VMD alarm group – VMD alarm group. VMD zone – VMD zone nr. VMD cycle – VMD measure cycle. alarm area – Alarm area. object class – OBTRACK object class. 78 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 78 --- GEUTEBRUCK18.42 Set system time Set system time. time stamp – Time stamp. 18.43 Set test picture mode Enable or disable test picture generator. channel – Channel. enable – Enable or disable test picture generator. 18.44 VCA set armed Send this action to notify VCA to be armed or disarmed. Channel – Channel. Sensor type – Sensor type. Armed (true) or disarmed (false) – Armed (true) or disarmed (false) 18.45 VCA status answer This action will be sent in response to VCA status request. Channel – Channel. Sensor type – Sensor type. Armed (true) or disarmed (false) – Armed (true) or disarmed (false) 18.46 VCA status request Send this action to request status of VCA. As response VCA will send VCA status answer. Channel – Channel. Sensor type – Sensor type. 18.47 Video contrast detected This action will be fired when the contrast is detected in the video signal. channel – Channel. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 79 --- Page 79 --- GEUTEBRUCK18.48 Video contrast failed This action will be fired when the contrast is lost in the video signal. channel – Channel. 18.49 Video set image brightness Video set image brightness. channel – Channel. sensor type – Sensor type. brightness – Brightness. 18.50 Video set image contrast Video set image contrast. channel – Channel. sensor type – Sensor type. contrast – Contrast. 18.51 Video set image saturation Video set image saturation. channel – Channel. sensor type – Sensor type. saturation – Saturation. 18.52 Video source has changed This action indicates the changes on the video input source. channel – Channel. signal norm – New signal norm. signal type – New signal type. interlace type – New interlace type. 80 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 80 --- GEUTEBRUCK18.53 Video sync detected This action will be fired when the sync is detected in the video signal. channel – Channel. 18.54 Video sync failed This action will be fired when the sync is lost in the video signal. channel – Channel. 19 Viewer actions All actions for viewer customizing. 19.1 VC alarm queue confirm Confirm alarm from the queue on the viewer client. viewer – Global viewer or viewer client no. selection mode – Selection mode. 19.2 VC alarm queue confirm by instance Confirm alarm from the queue on the viewer client. viewer – Global viewer or viewer client no. instance ID – Instance ID of the alarm. 19.3 VC alarm queue confirm by type Confirm alarm of specific type from the queue on the viewer client. viewer – Global viewer or viewer client no. event type – Type of the event. selection mode – Selection mode. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 81 --- Page 81 --- GEUTEBRUCK19.4 VC alarm queue remove Remove alarm from the queue on the viewer client. viewer – Global viewer or viewer client no. selection mode – Selection mode. 19.5 VC alarm queue remove by instance Remove alarm from the queue on the viewer client. viewer – Global viewer or viewer client no. instance ID – Instance ID of the alarm. 19.6 VC alarm queue remove by type Remove alarm of specific type from the queue on the viewer client. viewer – Global viewer or viewer client no. event type – Type of the event. selection mode – Selection mode. 19.7 VC alarm queue select Select alarm from the queue on the viewer client. viewer – Global viewer or viewer client no. selection mode – Selection mode. 19.8 VC alarm queue select by instance Select alarm from the queue on the viewer client. viewer – Global viewer or viewer client no. instance ID – Instance ID of the alarm. 19.9 VC alarm queue select by type Select alarm of specific type from the queue on the viewer client. viewer – Global viewer or viewer client no. event type – Type of the event. selection mode – Selection mode. 82 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 82 --- GEUTEBRUCK19.10 VC change scene by name Viewer client change scene by name. viewer – Global viewer or viewer client no. scene – Scene name. 19.11 VC clear scene by name Viewer client clear scene by name. viewer – Global viewer or viewer client no. scene – Scene name. 19.12 VC full mode Viewer client full mode. viewer – Global viewer or viewer client no. full mode – Switch viewer client in full mode. sensitive area enabled – Sensitive area enabled. 19.13 VC set audio level Viewer client set audio level. viewer – Global viewer or viewer client no. audio level – Audio level in range 0 (audio off) till 100 (max. volume). 19.14 VC show viewer text Viewer client show viewer text. viewer – Global viewer or viewer client no. show text – Show text in viewer client. 19.15 VC stretch mode Viewer client stretch mode. viewer – Global viewer or viewer client no. stretch mode – Switch viewer client in stretch mode. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 83 --- Page 83 --- GEUTEBRUCK19.16 Viewer change scene Viewer change scene. viewer – Global viewer or viewer client no. 19.17 Viewer change sync audio/video Viewer change sync audio/video. viewer – Global viewer or viewer client no. enable sync – Enable audio/video sync. 19.18 Viewer clear Clear viewer. viewer – Global viewer or viewer client no. 19.19 Viewer clear scene Viewer clear scene. viewer – Global viewer or viewer client no. 19.20 Viewer clear text output Clear text output in the given viewer. viewer – Global viewer or viewer client no. 19.21 Viewer connect Connect camera to the viewer. viewer – Global viewer or viewer client no. channel – Channel. play mode – Viewer play mode. 84 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 84 --- GEUTEBRUCK19.22 Viewer connect live Connect live camera to the viewer. viewer – Global viewer or viewer client no. channel – Channel. 19.23 Viewer export picture Viewer export picture. viewer – Global viewer or viewer client no. file path – File path (local or UNC). GSCView default path is used if left empty. 19.24 Viewer jump by time Viewer jump by time. viewer – Global viewer or viewer client no. channel – Channel. play mode – Viewer play mode. time in sec – Time to jump in seconds. Use negative values to jump in past. 19.25 Viewer maximize Viewer maximize. viewer – Global viewer or viewer client no. maximize – Maximize. 19.26 Viewer play from time Viewer play from time. viewer – Global viewer or viewer client no. channel – Channel. play mode – Viewer play mode. time – Time to play from. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 85 --- Page 85 --- GEUTEBRUCK19.27 Viewer print picture Viewer print picture. viewer – Global viewer or viewer client no. 19.28 Viewer select Select viewer. viewer – Global viewer or viewer client no. 19.29 Viewer set play mode Set play mode of the viewer. viewer – Global viewer or viewer client no. play mode – Viewer play mode. play speed – Optional play speed parameter. 19.30 Viewer show alarm by instance Show alarm in viewer using alarm instance ID. viewer – Global viewer or viewer client no. instance ID – Instance ID of the alarm. play mode – Viewer alarm’s play mode. 19.31 Viewer show alarm by key Show alarm in viewer using alarm foreign key. viewer – Global viewer or viewer client no. foreign key – Foreign key used to start the alarm. play mode – Viewer alarm’s play mode. 86 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 86 --- GEUTEBRUCK19.32 Viewer show alarm by type Show alarm in viewer using alarm type and optional foreign key. viewer – Global viewer or viewer client no. alarm type – Type of the alarm. foreign key – Foreign key used to start the alarm. play mode – Viewer alarm’s play mode. 19.33 Viewer text output Display free string in the given viewer. viewer – Global viewer or viewer client no. text string – Text string to display. 20 Viewer notifications All viewer notifications. 20.1 Image export notification Notification on export or print of channel images. user – Name of the user connected to the system. destination – Destination. destination type – Destination type. time stamp – Time stamp. end time – End time. channels – Channels. client host – Host from where the connection is done. client type – Client type. client account – User account from where the connection is done. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 87 --- Page 87 --- GEUTEBRUCK20.2 Scene store modification Scene store modification. viewer – Global viewer or viewer client no. scene store GUID – Scene store GUID. scene store name – Scene store name. time stamp – Time stamp. modification type – Modification type. user – Name of the user. client host – Host from where the connection is done. client type – Client type. client account – User account from where the connection is done. 20.3 VC alarm queue notification Alarm queue notification on the viewer client. viewer – Global viewer or viewer client no. notification – Alarm state notification. instance ID – Instance ID of the alarm. event type – Type of the event. client host – Host from where the connection is done. client type – Client type. client account – User account from where the connection is done. 20.4 VC scene changed Viewer client scene changed. viewer – Global viewer or viewer client no. scene – Scene name. 20.5 Viewer cleared Viewer cleared. viewer – Global viewer or viewer client no. client host – Host from where the connection is done. client type – Client type. client account – User account from where the connection is done. 88 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 88 --- GEUTEBRUCK20.6 Viewer connected Viewer connected to the camera. viewer – Global viewer or viewer client no. channel – Channel. play mode – Viewer play mode. client host – Host from where the connection is done. client type – Client type. client account – User account from where the connection is done. 20.7 Viewer play mode changed Viewer play mode changed. viewer – Global viewer or viewer client no. channel – Channel. play mode – Viewer play mode. channel time – Channel time. client host – Host from where the connection is done. client type – Client type. client account – User account from where the connection is done. 20.8 Viewer selection changed Viewer selection was changed. viewer – Global viewer or viewer client no. channel – Channel. play mode – Viewer play mode. client host – Host from where the connection is done. client type – Client type. client account – User account from where the connection is done. GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 89 --- Page 89 --- GEUTEBRUCKA Examples The following list contains the example notation of all GEVISCOPE actions. If the action has some optional parameters, then the notation without them is also given in the third line. Following numeric values used in this: 64 for 64 bit integer numbers, 32 for 32 bit integer numbers, 1 for boolean values, and 0 for enumeration types. ABCConnect ("address") ABCDisconnect () ABCPlayFile (64, "file name", 1) AbortAllAutoBackups () AbortAutoBackup ("schedule") ACSAccessDenied ("ACS", ACSNo: 32 ,Account: 64 , BancCode: 64 ,CardNo: "card no" ,TimeStamp: "2013/09/05 14:59:59,999 GMT+02:00" ,Reason: 32 ) ACSAccessDenied ("ACS") ACSAccessGranted ("ACS", ACSNo: 32 ,Account: 64 , BancCode: 64 ,CardNo: "card no" ,TimeStamp: "2013/09/05 14:59:59,999 GMT+02:00" ) ACSAccessGranted ("ACS") ACSRawAnswer ("ACS", "2013/09/05 14:59:59,999 GMT+02:00", "answer") ACSRawData ("ACS", "2013/09/05 14:59:59,999 GMT+02:00", "data") ActivateExternalProcess (32, "2013/09/05 14:59:59,999 GMT+02:00", 0) ATMRawAnswer ("ATM", "2013/09/05 14:59:59,999 GMT+02:00", "answer") ATMRawData ("ATM", "2013/09/05 14:59:59,999 GMT+02:00", "data") ATMTransaction ("ATM", 1, 32, ATMNo: 32 ,Account: 64 , BancCode: 64 ,CardNo: "card no" ,TAN1: 64 ,TAN2: 64,TimeStamp1: "2013/09/05 14:59:59,999 GMT+02:00" , TimeStamp2: "2013/09/05 14:59:59,999 GMT+02:00" , Amount: 0.0 ,Currency: "currency" ) ATMTransaction ("ATM", 1, 32) AutoBackupCapacityMonitoringCapacityWarning (0, "destination", 64, 64, 64, 32, 32, 32) AutoBackupCapacityMonitoringFileAutoDeleted (0, "destination", 64, 64, 64, 32, 32, 32, 64, "file name") AutoBackupCapacityMonitoringOutOfDiskSpace (0, "destination", 64, 64, 64, 32, 32, 32) AutoBackupFileDone ("schedule", StartTime: "2013/09/05 14:59:59,999 GMT+02:00" , 90 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 90 --- GEUTEBRUCK"2013/09/05 14:59:59,999 GMT+02:00", 32, 1, 32, "2013/09/05 14:59:59,999 GMT+02:00", "source", "destination", 64, 64, 32, "file name", 64) AutoBackupFileDone ("schedule", "2013/09/05 14:59:59,999 GMT+02:00", 32, 1, 32, "2013/09/05 14:59:59,999 GMT+02:00", "source", "destination", 64, 64, 32, "file name", 64) AutoBackupFileProgress ("schedule", StartTime: "2013/09/05 14:59:59,999 GMT+02:00" , "2013/09/05 14:59:59,999 GMT+02:00", 32, 1, 32, "2013/09/05 14:59:59,999 GMT+02:00", "source", "destination", 64, 64, 32, "file name", 64) AutoBackupFileProgress ("schedule", "2013/09/05 14:59:59,999 GMT+02:00", 32, 1, 32, "2013/09/05 14:59:59,999 GMT+02:00", "source", "destination", 64, 64, 32, "file name", 64) AutoBackupFileStarted ("schedule", StartTime: "2013/09/05 14:59:59,999 GMT+02:00" , "2013/09/05 14:59:59,999 GMT+02:00", 32, 1, 32, "2013/09/05 14:59:59,999 GMT+02:00", "source", "destination", 64, 64, 32, "file name") AutoBackupFileStarted ("schedule", "2013/09/05 14:59:59,999 GMT+02:00", 32, 1, 32, "2013/09/05 14:59:59,999 GMT+02:00", "source", "destination", 64, 64, 32, "file name") AutoBackupOperationDone ("schedule", StartTime: "2013/09/05 14:59:59,999 GMT+02:00" , "2013/09/05 14:59:59,999 GMT+02:00", 32, 1, 32, "2013/09/05 14:59:59,999 GMT+02:00", "2013/09/05 14:59:59,999 GMT+02:00", "source", "destination", 64, 64, OperationErrorCode: 32 ) AutoBackupOperationDone ("schedule", "2013/09/05 14:59:59,999 GMT+02:00", 32, 1, 32, "2013/09/05 14:59:59,999 GMT+02:00", "2013/09/05 14:59:59,999 GMT+02:00", "source", "destination", 64, 64) AutoBackupOperationStarted ("schedule", StartTime: "2013/09/05 14:59:59,999 GMT+02:00" , "2013/09/05 14:59:59,999 GMT+02:00", 32, 1, 32, "2013/09/05 14:59:59,999 GMT+02:00", "source", "destination", 64, 64) AutoBackupOperationStarted ("schedule", "2013/09/05 14:59:59,999 GMT+02:00", 32, 1, 32, "2013/09/05 14:59:59,999 GMT+02:00", "source", "destination", 64, 64) AutoBackupScheduleDone ("schedule", StartTime: "2013/09/05 14:59:59,999 GMT+02:00" , "2013/09/05 14:59:59,999 GMT+02:00", "2013/09/05 14:59:59,999 GMT+02:00", 32, 1) AutoBackupScheduleDone ("schedule", "2013/09/05 14:59:59,999 GMT+02:00", "2013/09/05 14:59:59,999 GMT+02:00", 32, 1) AutoBackupScheduleStarted ("schedule", StartTime: "2013/09/05 14:59:59,999 GMT+02:00" , "2013/09/05 14:59:59,999 GMT+02:00", 32, 1) AutoBackupScheduleStarted ("schedule", "2013/09/05 14:59:59,999 GMT+02:00", GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 91 --- Page 91 --- GEUTEBRUCK32, 1) AutoFocusOff (32) AutoFocusOn (32) BackupEvent (64, "event type", "destination", StartHintID: 64,StopHintID: 64 ,Subfolder: "sub folder" ) BackupEvent (64, "event type", "destination") BarcodeData ("scanner", "2013/09/05 14:59:59,999 GMT+02:00", "code") BlockingFilterActivate ("filter") BlockingFilterDeactivate ("filter") CameraApplyProfile (32, "profile") CameraBacklightCompensationMode (32, 0) CameraClearPrePosText (32, 32) CameraDayNightMode (32, 0) CameraLightOff (32) CameraLightOn (32) CameraManualIrisOff (32) CameraManualIrisOn (32) CameraOff (32) CameraOn (32) CameraPumpOff (32) CameraPumpOn (32) CameraRAWOutput (32, "output") CameraSelectCharMode (32, 32) CameraSetPrePosText (32, 32) CameraSpecFuncUOff (32) CameraSpecFuncUOn (32) CameraSpecFuncVOff (32) CameraSpecFuncVOn (32) CameraSpecFuncXOff (32) CameraSpecFuncXOn (32) CameraSpecFuncYOff (32) CameraSpecFuncYOn (32) CameraStopAll (32) CameraTextOff (32) CameraTextOn (32) CameraTourStart (32, 32, "tour name") CameraTourStop (32) 92 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 92 --- GEUTEBRUCKCameraVersionOff (32) CameraVersionOn (32) CameraWashOff (32) CameraWashOn (32) CancelExport ("00000000-0000-0000-0000-000000000000", 0) CaseClosed () CaseOpened () ChangeADParameterSet (32, "AD parameter set") ChangeCameraProfile ("hardware", "profile") ChangeCPAParameterSet (32, "CPA parameter set") ChangeGTectParameterSet (32, "GTect parameter set") ChangeObtrackParameterSet (32, "OBTRACK parameter set") ChangeVMDParameterSet (32, "VMD parameter set") ChannelError (32, SensorType: 0 , 0, 0, WindowsError: 32 , Description: "description" ,XMLInfo: "additional info" ) ChannelError (32, 0, 0) ChannelInfo (32, SensorType: 0 , 0, 0, Description: "description" ,XMLInfo: "additional info" ) ChannelInfo (32, 0, 0) ChannelLiveCheck (32, 0, "2013/09/05 14:59:59,999 GMT+02:00") ChannelWarning (32, SensorType: 0 , 0, 0, WindowsError: 32,Description: "description" ,XMLInfo: "additional info" ) ChannelWarning (32, 0, 0) CPAMeasurement (32, 32) CustomAction (64, "STRING parameter") DatabaseRecordingInfoRing (0, 1, 1, 1, 0.0, 0.0, 0.0, 0.0, 0.0, 64, "2013/09/05 14:59:59,999 GMT+02:00", RecordingDepth: 0.0 ,EstimatedRequiredCapacity: 64 ) DatabaseRecordingInfoRing (0, 1, 1, 1, 0.0, 0.0, 0.0, 0.0, 0.0, 64, "2013/09/05 14:59:59,999 GMT+02:00") DatabaseRecordingInfoTotal (1, 1, 1, 0.0, 0.0, 0.0, 0.0, 0.0, 64, 64, 64, OldestItem: "2013/09/05 14:59:59,999 GMT+02:00" , RecordingDepth: 0.0 ,EstimatedRequiredCapacity: 64 , RequiredCapacityFactor: 0.0 ,RequiredCapacityAvailable: 1) DatabaseRecordingInfoTotal (1, 1, 1, 0.0, 0.0, 0.0, 0.0, 0.0, 64, 64, 64) DatabaseStarted (0, 64) DefaultPosCallUp (32) DefaultPosClear (32) GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 93 --- Page 93 --- GEUTEBRUCKDefaultPosSave (32) DeviceFound ("device type", "device name", "serial ID") DeviceNewFirmware ("device type", "device name", "serial ID", "firmware serial") DevicePluginError (32, "device type", SubType: "device subtype" , "device name", "serial ID", 0, ErrorCode: 32,Description: "description" ) DevicePluginError (32, "device type", "device name", "serial ID", 0) DevicePluginState (32, "device type", SubType: "device subtype" , "device name", "serial ID", 0, InternalState: 32,Description: "description" ) DevicePluginState (32, "device type", "device name", "serial ID", 0) DeviceReattached ("device type", "device name", "serial ID") DeviceRemoved ("device type", "device name", "serial ID") DigitalInput (32, 0) EventBackupDone ("00000000-0000-0000-0000-000000000000", "event type", 64, "destination", 64, 64, "2013/09/05 14:59:59,999 GMT+02:00", "2013/09/05 14:59:59,999 GMT+02:00", OperationErrorCode: 32 ) EventBackupDone ("00000000-0000-0000-0000-000000000000", "event type", 64, "destination", 64, 64, "2013/09/05 14:59:59,999 GMT+02:00", "2013/09/05 14:59:59,999 GMT+02:00") EventBackupFileDone ("00000000-0000-0000-0000-000000000000", "event type", 64, "destination", 64, 64, "2013/09/05 14:59:59,999 GMT+02:00", 32, "file name", 64) EventBackupFileProgress ("00000000-0000-0000-0000-000000000000", "event type", 64, "destination", 64, 64, "2013/09/05 14:59:59,999 GMT+02:00", 32, "file name", 64) EventBackupFileStarted ("00000000-0000-0000-0000-000000000000", "event type", 64, "destination", 64, 64, "2013/09/05 14:59:59,999 GMT+02:00", 32, "file name") EventBackupStarted ("00000000-0000-0000-0000-000000000000", "event type", 64, "destination", 64, 64, "2013/09/05 14:59:59,999 GMT+02:00") EventRecordingChanged (64, "event type") EventStarted (64, "event type", ForeignKey: 64 ) EventStarted (64, "event type") EventStopped (64, "event type") ExportFinished ("00000000-0000-0000-0000-000000000000", 0) ExportProgress ("00000000-0000-0000-0000-000000000000", 32) 94 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 94 --- GEUTEBRUCKFastSpeedOff (32) FastSpeedOn (32) FillingPumpStatus ("terminal", "2013/09/05 14:59:59,999 GMT+02:00", 32, 0, Amount: 0.0 ,Price: 0.0 ,Details: "details" ) FillingPumpStatus ("terminal", "2013/09/05 14:59:59,999 GMT+02:00", 32, 0) FocusFar (32, 32) FocusNear (32, 32) FocusStop (32) FRCNotification (0, Param: 32 ,Description: "description" , XMLInfo: "additional info" ) FRCNotification (0) GEMOSalarm (64, 32, "GEMOS str") GSCSVehicleAccessDenied (32, "plate no.", "2013/09/05 14:59:59,999 GMT+02:00", CompanyCategory: "company category" ,CompanyName: "company name" , Reason: "reason" ,TrafficLane: "traffic lane" , Channel: 32 ,Direction: 0 ) GSCSVehicleAccessDenied (32, "plate no.", "2013/09/05 14:59:59,999 GMT+02:00") GSCSVehicleAccessExpired (32, "plate no.", "2013/09/05 14:59:59,999 GMT+02:00", "2013/09/05 14:59:59,999 GMT+02:00", CompanyCategory: "company category" ,CompanyName: "company name" , Reason: "reason" ,TrafficLane: "traffic lane" , Channel: 32 ,Direction: 0 ) GSCSVehicleAccessExpired (32, "plate no.", "2013/09/05 14:59:59,999 GMT+02:00", "2013/09/05 14:59:59,999 GMT+02:00") GSCSVehicleAccessGranted (32, "plate no.", "2013/09/05 14:59:59,999 GMT+02:00", CompanyCategory: "company category" ,CompanyName: "company name" , Reason: "reason" ,TrafficLane: "traffic lane" , Channel: 32 ,Direction: 0 ) GSCSVehicleAccessGranted (32, "plate no.", "2013/09/05 14:59:59,999 GMT+02:00") GSCSVehicleAccessPending (32, "plate no.", "2013/09/05 14:59:59,999 GMT+02:00", CompanyCategory: "company category" ,CompanyName: "company name" , Reason: "reason" ,TrafficLane: "traffic lane" , Channel: 32 ,Direction: 0 ) GSCSVehicleAccessPending (32, "plate no.", "2013/09/05 14:59:59,999 GMT+02:00") GTectAnalyticsLiveCheck () GTectDualSensorAlarm (32, SterileZoneNumber: 32 , VirtualFenceNumber: 32 ,VMDGroup: 0 ,VMDZone: 32 , VMDCycle: 0 ,AlarmArea:f0, 0, 0, 0g) GTectDualSensorAlarm (32) GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 95 --- Page 95 --- GEUTEBRUCKGTectDualSensorAlarmFinished (32) GTectSceneAlarm (32, 0) GTectSceneAlarmFinished (32, 0) GTectVMXAlarm (32, SterileZoneNumber: 32 , VirtualFenceNumber: 32 ,AlarmGroup: 32 ,TrackID: 32 , AlarmArea:f0, 0, 0, 0g) GTectVMXAlarm (32) GTectVMXAlarmFinished (32) IASSettingsChanged (32, 0) ImageExportNotification ("user", "destination", 0, "2013/09/05 14:59:59,999 GMT+02:00", TimeEnd: "2013/09/05 14:59:59,999 GMT+02:00" , "channels", ClientHost: "client host" ,ClientType: 0 , ClientAccount: "client account" ) ImageExportNotification ("user", "destination", 0, "2013/09/05 14:59:59,999 GMT+02:00", "channels") ImexCapacityFileAutoDeleted (0, "destination", 64, 64, 64, 32, 32, 32, 64, 32) ImexCapacityOutOfDiskSpace (0, "destination", 64, 64, 64, 32, 32, 32) ImexCapacityWarning (0, "destination", 64, 64, 64, 32, 32, 32) ImexExportEventImage (64, "event type", Destination: "destination" ,FilePath: "file name" ) ImexExportEventImage (64, "event type") ImexExportImageFromDB (32, Destination: "destination" , FilePath: "file name" ,PictureTime: "2013/09/05 14:59:59,999 GMT+02:00" ) ImexExportImageFromDB (32) ImexExportImageFromLiveStream (32, Destination: "destination" ,FilePath: "file name" ) ImexExportImageFromLiveStream (32) InitializeRemoteExport (32, "00000000-0000-0000-0000-000000000000") InterfaceRawAnswer ("interface", "2013/09/05 14:59:59,999 GMT+02:00", "answer") InterfaceRawData ("interface", "2013/09/05 14:59:59,999 GMT+02:00", "data") IOI43ResetMainboard () IOI43Temperature ("ID", 32) IOI43WDActivate () IOI43WDDeactivate () IOI43WDTrigger () IPCameraRawCommand ("url", User: "user" ,Password: "password" ,POST: "post" ) 96 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 96 --- GEUTEBRUCKIPCameraRawCommand ("url") IPCamFailoverNotification ("primary server", "secondary server", 32, 32, CameraParameters: "camera parameters" ) IPCamFailoverNotification ("primary server", "secondary server", 32, 32) IPCamFailoverRestore ("primary server", "secondary server", 32, 32, CameraParameters: "camera parameters" ) IPCamFailoverRestore ("primary server", "secondary server", 32, 32) IPSwitchOperation (0, "port no", Param: 32 ) IPSwitchOperation (0, "port no") IrisClose (32) IrisOpen (32) IrisStop (32) KeyPressed (0) KeyReleased (0) KillAllEvents () KillEvent ("event type") KillEventByID (64) LenelAccessEvent (ID: 0 ,Panel: "panel" ,Device: "device" , SecondaryDevice: 32 ,CardNumber: 64 ,AccessResult: 0,Type: 0 ,SubType: 32 , "description", SerialNumber: 32,TimeStamp: "2013/09/05 14:59:59,999 GMT+02:00" , AreaEnteredID: 32 ,AreaExitedID: 32 ,AssetID: "asset ID",CardholderEntered: 1 ,Duress: 1 ,ElevatorFloor: 32,FacilityCode: 32 ,IsReadableCard: 1 ,IssueCode: 32,CommServerHostName: "server host" ,EventText: "event text" ) LenelAccessEvent ("description") LenelFireEvent (ID: 0 ,Panel: "panel" ,Device: "device" , SecondaryDevice: 32 ,TroubleCode: 32 ,Type: 0 , SubType: 32 , "description", SerialNumber: 32 , TimeStamp: "2013/09/05 14:59:59,999 GMT+02:00" , CommServerHostName: "server host" ,EventText: "event text" ) LenelFireEvent ("description") LenelIntercomEvent (ID: 0 ,Panel: "panel" , Device: "device" ,SecondaryDevice: 32 , IntercomData: 32 ,LineNumber: 32 ,Type: 0 , SubType: 32 , "description", SerialNumber: 32 , TimeStamp: "2013/09/05 14:59:59,999 GMT+02:00" , CommServerHostName: "server host" ,EventText: "event text" ) LenelIntercomEvent ("description") LenelRawData ("2013/09/05 14:59:59,999 GMT+02:00", "data") LenelRefreshNames () GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 97 --- Page 97 --- GEUTEBRUCKLenelSecurityEvent (ID: 0 ,Panel: "panel" ,Device: "device" ,SecondaryDevice: 32 ,Type: 0 , SubType: 32 , "description", SerialNumber: 32 , TimeStamp: "2013/09/05 14:59:59,999 GMT+02:00" , CommServerHostName: "server host" ,EventText: "event text" ) LenelSecurityEvent ("description") LenelVideoEvent (ID: 0 ,Panel: "panel" ,Device: "device" , SecondaryDevice: 32 ,Channel: 32 ,Type: 0 , SubType: 32 , "description", SerialNumber: 32 , TimeStamp: "2013/09/05 14:59:59,999 GMT+02:00" , StartTime: "2013/09/05 14:59:59,999 GMT+02:00" , EndTime: "2013/09/05 14:59:59,999 GMT+02:00" , CommServerHostName: "server host" ,EventText: "event text" ) LenelVideoEvent ("description") LiveCheck (64, "2013/09/05 14:59:59,999 GMT+02:00") LogBarcodeData ("barcode", Hash: 64 ,Scanner: "scanner name" ,AreaID: 64 ,AreaName: "area name" ,Channel: 32,TimeStamp: "2013/09/05 14:59:59,999 GMT+02:00" , Order: "order number" ,Shipment: "shipment number" , Item: "item number" ) LogBarcodeData ("barcode") LogBarcodeDataLPS ("barcode", Hash: 64 ,Scanner: "scanner name" ,AreaID: 64 ,AreaName: "area name" ,Channel: 32,TimeStamp: "2013/09/05 14:59:59,999 GMT+02:00" , X: 0.0 ,Y: 0.0 ,Z: 0.0 ,LpsTagID: 32 ,LpsStatus: 0 , LpsCellID: 32 ,LpsAreaID: 32 ,UserParam: 32 ,Order: "order number" ,Shipment: "shipment number" ,Item: "item number" ) LogBarcodeDataLPS ("barcode") LogNPRRecognition ("plate no.", Hash: 64 , Country: "country" ,Channel: 32 ,TimeStamp: "2013/09/05 14:59:59,999 GMT+02:00" ,Restriction: 0 , Category: "category" ) LogNPRRecognition ("plate no.") LPSPositionData (32, ScannerID: "scanner ID" , 64, 64, Z: 64,Latitude: 0.0 ,Longitude: 0.0 , 32, CellID: 32 , 0, TimeStamp: "2013/09/05 14:59:59,999 GMT+02:00" ,Data: "data" ,AreaName: "area name" ) LPSPositionData (32, 64, 64, 32, 0) LPSQueryPosition (32, ScannerID: "scanner ID" ,Data: "data" ) LPSQueryPosition (32) MakeCPAReferenceImage (32) MediaChannelSetupInfo (32, "2013/09/05 14:59:59,999 GMT+02:00", "parameter") MoveToAbsolutePosition (32, 0.0, 0.0, 0.0, 0.0) MoveToBySpeed (32, 0.0, 0.0) 98 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 98 --- GEUTEBRUCKMoveToRelativePosition (32, 0.0, 0.0, 0.0, 0.0) NPRRawData ("plate no.", "country", 32, "2013/09/05 14:59:59,999 GMT+02:00", f0, 0, 0, 0g, 32, 32, 32, 32, 32, 32, 1, 32, 32, 32, 32, "type") NPRRecognition ("plate no.", "country", 32, "2013/09/05 14:59:59,999 GMT+02:00", f0, 0, 0, 0g, 0, "category", 32, 32, 32, "type", 32) ObtrackChannelCounter (32, 0, 64, 32, "2013/09/05 14:59:59,999 GMT+02:00", ResetTimeStamp: "2013/09/05 14:59:59,999 GMT+02:00" ) ObtrackChannelCounter (32, 0, 64, 32, "2013/09/05 14:59:59,999 GMT+02:00") ObtrackChannelCounterThreshold (32, 0, 64, 0, "2013/09/05 14:59:59,999 GMT+02:00") ObtrackChannelSetCounter (32, 0, 64, "2013/09/05 14:59:59,999 GMT+02:00") ObtrackFrameRawData ("2013/09/05 14:59:59,999 GMT+02:00", 32, 32, 32) ObtrackGroupCounter (32, 0, 64, 32, "2013/09/05 14:59:59,999 GMT+02:00", ResetTimeStamp: "2013/09/05 14:59:59,999 GMT+02:00" , GroupName: "group name" ) ObtrackGroupCounter (32, 0, 64, 32, "2013/09/05 14:59:59,999 GMT+02:00") ObtrackGroupCounterThreshold (32, 0, 64, 0, "2013/09/05 14:59:59,999 GMT+02:00", GroupName: "group name" ) ObtrackGroupCounterThreshold (32, 0, 64, 0, "2013/09/05 14:59:59,999 GMT+02:00") ObtrackGroupSetCounter (32, 0, 64, "2013/09/05 14:59:59,999 GMT+02:00", GroupName: "group name" ) ObtrackGroupSetCounter (32, 0, 64, "2013/09/05 14:59:59,999 GMT+02:00") ObtrackObjectRawData ("2013/09/05 14:59:59,999 GMT+02:00", 32, 32, 32, 0, 0, Confidence: 32 ,Position:f0, 0, 0, 0g,Speed: 0.0 ,Duration: 32 ,Direction: 32 , Size: 0.0 ,ObjectWidth: 0.0 ,ObjectHeight: 0.0 , ProcessSize: 0 ,GscNetName: "GSC net name" ) ObtrackObjectRawData ("2013/09/05 14:59:59,999 GMT+02:00", 32, 32, 32, 0, 0) ObtrackTunnelAlarm (32, "2013/09/05 14:59:59,999 GMT+02:00", 0, 32, 32, ObjectArea: f0, 0, 0, 0g) ObtrackTunnelAlarm (32, "2013/09/05 14:59:59,999 GMT+02:00", 0, 32, 32) PanAuto (32, 32) PanLeft (32, 32) PanRight (32, 32) PanStop (32) POSData ("POS", "2013/09/05 14:59:59,999 GMT+02:00", Article: "article" ,Price: 0.0 ,Units: 32 , PricePerUnit: 0.0 ,Line1: "line 1" ,Line2: "line 2",Line3: "line 3" ,Line4: "line 4" ,Line5: "line 5") GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 99 --- Page 99 --- GEUTEBRUCKPOSData ("POS", "2013/09/05 14:59:59,999 GMT+02:00") POSStatus ("POS", "2013/09/05 14:59:59,999 GMT+02:00", 0, Details: "details" ) POSStatus ("POS", "2013/09/05 14:59:59,999 GMT+02:00", 0) PPDeviceAlarm ("interface id", 32, 0, 0) PPDeviceInput ("interface id", 32, 32, 0) PPDeviceOffline ("interface id", 32) PPDeviceOnline ("interface id", 32) PPInterfaceOffline ("interface id") PPInterfaceOnline ("interface id") PPQueryInterface ("interface id") PPSetDeviceOutput ("interface id", 32, 32, 0) PPSubcellAlarm ("interface id", 32, 0, 32, 0) PPZoneAlarm ("zone id", "interface id", 32, Cable: 0 , Subcell: 32 , 0) PPZoneAlarm ("zone id", "interface id", 32, 0) PrePosCallUp (32, 32) PrePosClear (32, 32) PrePosSave (32, 32) RedundantPowerFailure () RedundantPowerOk () ResetMainboard () SafebagClose (32, "2013/09/05 14:59:59,999 GMT+02:00", "2013/09/05 14:59:59,999 GMT+02:00", "safebag no.", "safebag info", 0, Debit: 0.0 ,Total: 0.0 , Difference: 0.0 ,HasDifference: 1 ,Notes: "notes" , Coins: "coins" ,Cheques: "cheques" ) SafebagClose (32, "2013/09/05 14:59:59,999 GMT+02:00", "2013/09/05 14:59:59,999 GMT+02:00", "safebag no.", "safebag info", 0) SafebagData (32, "2013/09/05 14:59:59,999 GMT+02:00", "safebag no.", "safebag info", 0, Debit: 0.0 ,Total: 0.0,Difference: 0.0 ,HasDifference: 1 ,Notes: "notes" ,Coins: "coins" ,Cheques: "cheques" ) SafebagData (32, "2013/09/05 14:59:59,999 GMT+02:00", "safebag no.", "safebag info", 0) SafebagOpen (32, "2013/09/05 14:59:59,999 GMT+02:00", "safebag no.", "safebag info", 0) SafebagPassingOfRiskData (32, "2013/09/05 14:59:59,999 GMT+02:00", "safebag no.", "safebag info", 0, 32, 32, TourNumber: 32,TargetWorkingPlace: "target working place" , PassingOfRiskType: "passing of risk type" ) SafebagPassingOfRiskData (32, "2013/09/05 14:59:59,999 GMT+02:00", "safebag no.", "safebag info", 0, 32, 32) 100 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 100 --- GEUTEBRUCKSafebagPassingOfRiskStart (32, "2013/09/05 14:59:59,999 GMT+02:00", "safebag no.", "safebag info", 0, 32, 32, TourNumber: 32,TargetWorkingPlace: "target working place" , PassingOfRiskType: "passing of risk type" ) SafebagPassingOfRiskStart (32, "2013/09/05 14:59:59,999 GMT+02:00", "safebag no.", "safebag info", 0, 32, 32) SafebagPassingOfRiskStop (32, "2013/09/05 14:59:59,999 GMT+02:00", "2013/09/05 14:59:59,999 GMT+02:00", "safebag no.", "safebag info", 0, 32, 32, TourNumber: 32 , TargetWorkingPlace: "target working place" , PassingOfRiskType: "passing of risk type" ) SafebagPassingOfRiskStop (32, "2013/09/05 14:59:59,999 GMT+02:00", "2013/09/05 14:59:59,999 GMT+02:00", "safebag no.", "safebag info", 0, 32, 32) SceneStoreModification (32, "00000000-0000-0000-0000-000000000000", "scene store name", "2013/09/05 14:59:59,999 GMT+02:00", 0, "user", ClientHost: "client host" ,ClientType: 0 , ClientAccount: "client account" ) SceneStoreModification (32, "00000000-0000-0000-0000-000000000000", "scene store name", "2013/09/05 14:59:59,999 GMT+02:00", 0, "user") SensorAlarmFinished (32, 0) SensorAudioAlarm (32) SensorInhibitAlarmFinished (32, 0) SensorInhibitVideoAlarm (32, 0, ADArea: 0 ,ADCell: 32 , VMDGroup: 0 ,VMDZone: 32 ,VMDCycle: 0 ,AlarmArea:f 0, 0, 0, 0g,ObjectClass: 0 ) SensorInhibitVideoAlarm (32, 0) SensorVideoAlarm (32, 0, ADArea: 0 ,ADCell: 32 ,VMDGroup: 0,VMDZone: 32 ,VMDCycle: 0 ,AlarmArea:f0, 0, 0, 0 g,ObjectClass: 0 ) SensorVideoAlarm (32, 0) SetCameraText (32, "text") SetClientVCA (32, 0, 1) SetClock ("2013/09/05 14:59:59,999 GMT+02:00") SetDigitalOutput (32, 0) SetExportMarker (32, 0) SetLED (0, 0) SetLEDBlink (0, 32, 32) SetSystemTime ("2013/09/05 14:59:59,999 GMT+02:00") SetTestPictureMode (32, 1) SetupChanged ("user name", "remote host", "2013/09/05 14:59:59,999 GMT+02:00", 0, "resource ID", 0,Details: "details" ,ClientHost: "client host" , ClientType: 0 ,ClientAccount: "client account" ) SetupChanged ("user name", "remote host", GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 101 --- Page 101 --- GEUTEBRUCK"2013/09/05 14:59:59,999 GMT+02:00", 0, "resource ID", 0) SetupUploadProgress (User1: "first user" ,User2: "second user" ,Host: "remote host" , 32, "2013/09/05 14:59:59,999 GMT+02:00") SetupUploadProgress (32, "2013/09/05 14:59:59,999 GMT+02:00") SetWatchdog (32) SkidataControl ("interface", 0) SkidataDeviceEvent ("interface", 32, 32) SkidataEntry ("interface", 0, "transaction", 32, 32) SkidataExit ("interface", 0, "transaction", 32, 32) SkidataTransaction ("interface", 0, "transaction", 32, 32) SMRPViewerCleared () SMRPViewerConnected ("server", 32) SMTPMailSend ("subject", "to", "cc", "body", Channel: 32 ) SMTPMailSend ("subject", "to", "cc", "body") StartAutoBackup ("schedule") StartEvent ("event type", ForeignKey: 64 ) StartEvent ("event type") StartRemoteExport ("00000000-0000-0000-0000-000000000000", "00000000-0000-0000-0000-000000000000", 0, 32, "2013/09/05 14:59:59,999 GMT+02:00", "2013/09/05 14:59:59,999 GMT+02:00", "job ID") StartSceneStore ("00000000-0000-0000-0000-000000000000", "cut-list", 64, 64) StopAllEvents () StopEvent ("event type") StopEventByID (64) SystemError (0, 0, WindowsError: 32 ,Description: "description" ,XMLInfo: "additional info" ) SystemError (0, 0) SystemInfo (0, 0, Description: "description" ,XMLInfo: "additional info" ) SystemInfo (0, 0) SystemSettingsChanged (1, User1: "first user" , User2: "second user" ,Host: "remote host" , 1,TimeRange: "current time range" , 1, "2013/09/05 14:59:59,999 GMT+02:00") SystemSettingsChanged (1, 1, 1, "2013/09/05 14:59:59,999 GMT+02:00") SystemStarted ("2013/09/05 14:59:59,999 GMT+02:00") SystemTerminating ("2013/09/05 14:59:59,999 GMT+02:00", 1) SystemWarning (0, 0, WindowsError: 32 ,Description: "description" ,XMLInfo: "additional info" ) 102 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 102 --- GEUTEBRUCKSystemWarning (0, 0) Temperature (0, "ID", 32) TerminalArticleData ("terminal", "2013/09/05 14:59:59,999 GMT+02:00", 32, PumpNo: 32 , 1, Amount: 0.0 ,Price: 0.0 ,Details: "details" ) TerminalArticleData ("terminal", "2013/09/05 14:59:59,999 GMT+02:00", 32, 1) TerminalPaymentData ("terminal", "2013/09/05 14:59:59,999 GMT+02:00", 32, PumpNo: 32 , 1, Amount: 0.0 ,Price: 0.0 ,Details: "details" ) TerminalPaymentData ("terminal", "2013/09/05 14:59:59,999 GMT+02:00", 32, 1) TiltDown (32, 32) TiltStop (32) TiltUp (32, 32) TransferBinaryBuffer ("00000000-0000-0000-0000-000000000000", "parameter") TransferBinaryChannelBuffer (32, "00000000-0000-0000-0000-000000000000", "parameter") UserLogin ("first user", User2: "second user" , "remote host", ClientHost: "client host" ,ClientType: 0 , ClientAccount: "client account" ) UserLogin ("first user", "remote host") UserLoginFailed ("first user", User2: "second user" , "remote host", 0, ClientHost: "client host" , ClientType: 0 ,ClientAccount: "client account" ) UserLoginFailed ("first user", "remote host", 0) UserLogout ("first user", User2: "second user" , "remote host", ClientHost: "client host" ,ClientType: 0 , ClientAccount: "client account" ) UserLogout ("first user", "remote host") VCAlarmQueueConfirm (32, 0) VCAlarmQueueConfirmByInstance (32, 64) VCAlarmQueueConfirmByType (32, "event type", 0) VCAlarmQueueNotification (32, 0, 64, "event type", ClientHost: "client host" ,ClientType: 0 , ClientAccount: "client account" ) VCAlarmQueueNotification (32, 0, 64, "event type") VCAlarmQueueRemove (32, 0) VCAlarmQueueRemoveByInstance (32, 64) VCAlarmQueueRemoveByType (32, "event type", 0) VCAlarmQueueSelect (32, 0) VCAlarmQueueSelectByInstance (32, 64) VCAlarmQueueSelectByType (32, "event type", 0) GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 103 --- Page 103 --- GEUTEBRUCKVCASetArmed (32, 0, 1) VCAStatusAnswer (32, 0, 1) VCAStatusRequest (32, 0) VCChangeSceneByName (32, "scene") VCClearSceneByName (32, "scene") VCFullMode (32, 1, 1) VCSceneChanged (32, "scene") VCSetAudioLevel (32, 32) VCShowViewerText (32, 1) VCStretchMode (32, 1) VideoContrastDetected (32) VideoContrastFailed (32) VideoSetImageBrightness (32, 0, 32) VideoSetImageContrast (32, 0, 32) VideoSetImageSaturation (32, 0, 32) VideoSourceChanged (32, 0, 0, 0) VideoSyncDetected (32) VideoSyncFailed (32) ViewerChangeScene (32) ViewerClear (32) ViewerCleared (32, ClientHost: "client host" ,ClientType: 0,ClientAccount: "client account" ) ViewerCleared (32) ViewerClearScene (32) ViewerClearTextOutput (32) ViewerConnect (32, 32, 0) ViewerConnected (32, 32, 0, ClientHost: "client host" , ClientType: 0 ,ClientAccount: "client account" ) ViewerConnected (32, 32, 0) ViewerConnectLive (32, 32) ViewerExportPicture (32, "file path") ViewerJumpByTime (32, 32, 0, 32) ViewerMaximize (32, 1) ViewerPlayFromTime (32, 32, 0, "2013/09/05 14:59:59,999 GMT+02:00") ViewerPlayModeChanged (32, 32, 0, ChannelTime: "2013/09/05 14:59:59,999 GMT+02:00" ,ClientHost: "client host" ,ClientType: 0 ,ClientAccount: "client account" ) ViewerPlayModeChanged (32, 32, 0) ViewerPrintPicture (32) 104 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 104 --- GEUTEBRUCKViewerSelect (32) ViewerSelectionChanged (32, 32, 0, ClientHost: "client host" ,ClientType: 0 ,ClientAccount: "client account" ) ViewerSelectionChanged (32, 32, 0) ViewerSetPlayMode (32, 0, 32) ViewerShowAlarmByInstance (32, 64, 0) ViewerShowAlarmByKey (32, 64, 0) ViewerShowAlarmByType (32, "alarm type", ForeignKey: 64 , 0) ViewerShowAlarmByType (32, "alarm type", 0) ViewerSyncAudioAndVideo (32, 1) ViewerTextOutput (32, "text string") WatchdogActivate () WatchdogDeactivate () WatchdogTrigger () ZoomIn (32, 32) ZoomOut (32, 32) ZoomStop (32) GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 105 --- Page 105 --- GEUTEBRUCK106 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 106 --- GEUTEBRUCKIndex Action classes, 15 ATM/ACS, 16 Audio control, 18 Backup actions, 19 Camera control, 26 Cash management actions, 35 Device information, 38 Digital contacts, 40 Imex, 42 LPS, 44 Lenel, 45 Supply chain security, 56 POS, 49 Perimeter protection, 51 Remote export, 53 SKIDATA, 55 System actions, 59 Video control, 68 Viewer notifications, 87 Viewer actions, 81 Actions by name ABC connect, 18 ABC disconnect, 18 ABC play file, 19 Abort all auto backups, 19 Abort auto backup, 19 ACS access denied, 16 ACS access granted, 17 ACS raw answer, 17 ACS raw data, 17Activate external process, 68 ATM raw answer, 17 ATM raw data, 17 ATM transaction, 18 Auto backup capacity file auto deleted, 19 Auto backup capacity out of disk space, 20 Auto backup capacity warning, 20 Auto backup file done, 21 Auto backup file progress, 21 Auto backup file started, 22 Auto backup operation done, 22 Auto backup operation started, 23 Auto backup schedule done, 23 Auto backup schedule started, 23 Auto focus off, 26 Auto focus on, 26 Backup event, 24 Barcode data, 49 Blocking filter activate, 59 Blocking filter deactivate, 59 Camera apply profile, 26 Camera backlight compensation mode, 26 Camera clear preset text, 27 Camera day/night mode, 27 Camera light off, 27 Camera light on, 27 Camera manual iris off, 27 Camera manual iris on, 27 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 107 --- Page 107 --- GEUTEBRUCKCamera off, 27 Camera on, 28 Camera pump off, 28 Camera pump on, 28 Camera RAW output, 26 Camera select char mode, 28 Camera set preset text, 28 Camera spec func U off, 28 Camera spec func U on, 28 Camera spec func V off, 29 Camera spec func V on, 29 Camera spec func X off, 29 Camera spec func X on, 29 Camera spec func Y off, 29 Camera spec func Y on, 29 Camera stop all, 29 Camera text off, 30 Camera text on, 30 Camera tour start, 30 Camera tour stop, 30 Camera version off, 30 Camera version on, 30 Camera wash-wipe off, 30 Camera wash-wipe on, 31 Cancel export, 53 Case has been closed, 40 Case has been opened, 40 Change AD parameter set, 68 Change camera profile, 69 Change CPA parameter set, 69 Change GTectVMX parameter set, 69 Change OBTRACK parameter set, 69 Change VMD parameter set, 69Channel error, 69 Channel info, 70 Channel live check, 70 Channel warning, 70 Clear default position, 31 Clear preset position, 31 CPA measurement, 68 Custom action, 59 Database recording info per ring, 60 Database recording info total, 60 Database started, 61 Device found, 38 Device plugin error, 38 Device plugin state, 39 Device reattached, 39 Device removed, 39 Digital input, 40 Enable client VCA, 71 Event backup done, 24 Event backup file done, 24 Event backup file progress, 25 Event backup file started, 25 Event backup started, 25 Event recording changed, 61 Event started, 61 Event stopped, 61 Export finished, 53 Export progress, 54 Fast speed off, 31 Fast speed on, 31 Filling pump status, 49 Focus far, 31 Focus near, 31 Focus stop, 32 108 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 108 --- GEUTEBRUCKFRC notification, 61 G-Tect analytics live check, 71 G-Tect scene alarm, 71 G-Tect scene alarm finished, 71 G-Tect/Dual sensor alarm, 71 G-Tect/Dual sensor alarm finished, 72 G-Tect/VMX alarm, 72 G-Tect/VMX alarm finished, 72 GEMOS alarm, 62 GSCS vehicle access denied, 56 GSCS vehicle access expired, 56 GSCS vehicle access granted, 57 GSCS vehicle access pending, 57 IAS settings changed, 72 Image export notification, 87 Imex capacity file auto deleted, 43 Imex capacity out of disk space., 43 Imex capacity warning, 43 Imex export event image, 44 Imex export image from DB, 44 Imex export image from live stream, 44 Initialize remote export, 54 Interface raw answer, 49 Interface raw data, 49 IOI43 reset mainboard, 40 IOI43 temperature notification, 40 IOI43 watchdog activate, 40 IOI43 watchdog deactivate, 41 IOI43 watchdog trigger, 41 IP camera failover notification, 72 IP camera failover restore, 73 IP camera raw command, 73 IP switch operation, 62Iris close, 32 Iris open, 32 Iris stop, 32 Key pressed, 41 Key released, 41 Kill all events, 62 Kill event, 62 Kill event by instance, 62 Lenel access event, 45 Lenel fire event, 46 Lenel intercom event, 47 Lenel raw data, 47 Lenel refresh names, 47 Lenel security event, 48 Lenel video event, 48 Live check, 62 Log barcode data, 58 Log barcode data LPS, 58 Log NPR recognition, 58 LPS position data, 44 LPS query position, 45 Make CPA reference image, 73 Media channel setup, 73 Move by speed, 32 Move to absolute position, 32 Move to default position, 33 Move to preset position, 33 Move to relative position, 33 New firmware received, 39 NPR raw data, 74 NPR recognition, 74 OBTRACK channel counter, 75 OBTRACK channel counter thresh- old, 75 OBTRACK channel set counter, 75 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 109 --- Page 109 --- GEUTEBRUCKOBTRACK frame raw data, 75 OBTRACK group counter, 76 OBTRACK group counter thresh- old, 76 OBTRACK group set counter, 76 OBTRACK object raw data, 77 OBTRACK tunnel alarm, 77 Pan auto, 33 Pan left, 33 Pan right, 33 Pan stop, 34 POS data, 50 POS status, 50 PP device alarm, 51 PP device input, 51 PP device offline, 52 PP device online, 52 PP interface offline, 52 PP interface online, 52 PP query interface, 52 PP set device output, 52 PP subcell alarm, 53 PP zone alarm, 53 Redundant power failure, 63 Redundant power ok, 63 Reset mainboard, 41 Safebag close, 35 Safebag data, 36 Safebag open, 36 Safebag passing of risk data, 37 Safebag passing of risk start, 37 Safebag passing of risk stop, 37 Save default position, 34 Save preset position, 34 Scene store modification, 88Sensor alarm finished, 77 Sensor audio alarm, 19 Sensor inhibit alarm finished, 78 Sensor inhibit video alarm, 78 Sensor video alarm, 78 Set camera text, 34 Set clock, 63 Set digital output, 41 Set export marker, 54 Set system LED, 41 Set system LED to blink, 42 Set system time, 79 Set test picture mode, 79 Set watchdog, 64 Setup changed, 64 Setup upload progress, 64 SKIDATA control, 55 SKIDATA device event, 55 SKIDATA entry, 55 SKIDATA exit, 55 SKIDATA transaction, 56 SMRP viewer cleared, 63 SMRP viewer connected, 63 SMTP mail, 63 Start auto backup, 26 Start event, 64 Start remote export, 54 Start scene store, 54 Stop all events, 65 Stop event, 65 Stop event by instance, 65 System error, 65 System info, 65 System settings changed, 66 110 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 110 --- GEUTEBRUCKSystem started, 66 System terminating, 66 System warning, 66 Temperature notification, 42 Terminal article data, 50 Terminal payment data, 51 Tilt down, 34 Tilt stop, 34 Tilt up, 35 Transfer binary buffer, 67 Transfer binary channel buffer, 67 User login, 67 User login failed, 67 User logout, 68 VC alarm queue confirm, 81 VC alarm queue confirm by in- stance, 81 VC alarm queue confirm by type, 81 VC alarm queue notification, 88 VC alarm queue remove, 82 VC alarm queue remove by in- stance, 82 VC alarm queue remove by type, 82 VC alarm queue select, 82 VC alarm queue select by instance, 82 VC alarm queue select by type, 82 VC change scene by name, 83 VC clear scene by name, 83 VC full mode, 83 VC scene changed, 88 VC set audio level, 83 VC show viewer text, 83 VC stretch mode, 83VCA set armed, 79 VCA status answer, 79 VCA status request, 79 Video contrast detected, 79 Video contrast failed, 80 Video set image brightness, 80 Video set image contrast, 80 Video set image saturation, 80 Video source has changed, 80 Video sync detected, 81 Video sync failed, 81 Viewer change scene, 84 Viewer change sync audio/video, 84 Viewer clear, 84 Viewer clear scene, 84 Viewer clear text output, 84 Viewer cleared, 88 Viewer connect, 84 Viewer connect live, 85 Viewer connected, 89 Viewer export picture, 85 Viewer jump by time, 85 Viewer maximize, 85 Viewer play from time, 85 Viewer play mode changed, 89 Viewer print picture, 86 Viewer select, 86 Viewer selection changed, 89 Viewer set play mode, 86 Viewer show alarm by instance, 86 Viewer show alarm by key, 86 Viewer show alarm by type, 87 Viewer text output, 87 Watchdog activate, 42 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 111 --- Page 111 --- GEUTEBRUCKWatchdog deactivate, 42 Watchdog trigger, 42 Zoom in, 35 Zoom out, 35 Zoom stop, 35 Actions by shortcut ABCConnect, 18 ABCDisconnect, 18 ABCPlayFile, 19 AbortAllAutoBackups, 19 AbortAutoBackup, 19 ACSAccessDenied, 16 ACSAccessGranted, 17 ACSRawAnswer, 17 ACSRawData, 17 ActivateExternalProcess, 68 ATMRawAnswer, 17 ATMRawData, 17 ATMTransaction, 18 AutoBackupCapacityMonitoringCa- pacityWarning, 20 AutoBackupCapacityMonitoring- FileAutoDeleted, 19 AutoBackupCapacityMoni- toringOutOfDiskSpace, 20 AutoBackupFileDone, 21 AutoBackupFileProgress, 21 AutoBackupFileStarted, 22 AutoBackupOperationDone, 22 AutoBackupOperationStarted, 23 AutoBackupScheduleDone, 23 AutoBackupScheduleStarted, 23 AutoFocusOff, 26 AutoFocusOn, 26 BackupEvent, 24 BarcodeData, 49BlockingFilterActivate, 59 BlockingFilterDeactivate, 59 CameraApplyProfile, 26 CameraBacklightCompensation- Mode, 26 CameraClearPrePosText, 27 CameraDayNightMode, 27 CameraLightOff, 27 CameraLightOn, 27 CameraManualIrisOff, 27 CameraManualIrisOn, 27 CameraOff, 27 CameraOn, 28 CameraPumpOff, 28 CameraPumpOn, 28 CameraRAWOutput, 26 CameraSelectCharMode, 28 CameraSetPrePosText, 28 CameraSpecFuncUOff, 28 CameraSpecFuncUOn, 28 CameraSpecFuncVOff, 29 CameraSpecFuncVOn, 29 CameraSpecFuncXOff, 29 CameraSpecFuncXOn, 29 CameraSpecFuncYOff, 29 CameraSpecFuncYOn, 29 CameraStopAll, 29 CameraTextOff, 30 CameraTextOn, 30 CameraTourStart, 30 CameraTourStop, 30 CameraVersionOff, 30 CameraVersionOn, 30 CameraWashOff, 30 CameraWashOn, 31 112 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 112 --- GEUTEBRUCKCancelExport, 53 CaseClosed, 40 CaseOpened, 40 ChangeADParameterSet, 68 ChangeCameraProfile, 69 ChangeCPAParameterSet, 69 ChangeGTectParameterSet, 69 ChangeObtrackParameterSet, 69 ChangeVMDParameterSet, 69 ChannelError, 69 ChannelInfo, 70 ChannelLiveCheck, 70 ChannelWarning, 70 CPAMeasurement, 68 CustomAction, 59 DatabaseRecordingInfoRing, 60 DatabaseRecordingInfoTotal, 60 DatabaseStarted, 61 DefaultPosCallUp, 33 DefaultPosClear, 31 DefaultPosSave, 34 DeviceFound, 38 DeviceNewFirmware, 39 DevicePluginError, 38 DevicePluginState, 39 DeviceReattached, 39 DeviceRemoved, 39 DigitalInput, 40 EventBackupDone, 24 EventBackupFileDone, 24 EventBackupFileProgress, 25 EventBackupFileStarted, 25 EventBackupStarted, 25 EventRecordingChanged, 61EventStarted, 61 EventStopped, 61 ExportFinished, 53 ExportProgress, 54 FastSpeedOff, 31 FastSpeedOn, 31 FillingPumpStatus, 49 FocusFar, 31 FocusNear, 31 FocusStop, 32 FRCNotification, 61 GEMOSalarm, 62 GSCSVehicleAccessDenied, 56 GSCSVehicleAccessExpired, 56 GSCSVehicleAccessGranted, 57 GSCSVehicleAccessPending, 57 GTectAnalyticsLiveCheck, 71 GTectDualSensorAlarm, 71 GTectDualSensorAlarmFinished, 72 GTectSceneAlarm, 71 GTectSceneAlarmFinished, 71 GTectVMXAlarm, 72 GTectVMXAlarmFinished, 72 IASSettingsChanged, 72 ImageExportNotification, 87 ImexCapacityFileAutoDeleted, 43 ImexCapacityOutOfDiskSpace, 43 ImexCapacityWarning, 43 ImexExportEventImage, 44 ImexExportImageFromDB, 44 ImexExportImageFromLiveStream, 44 InitializeRemoteExport, 54 InterfaceRawAnswer, 49 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 113 --- Page 113 --- GEUTEBRUCKInterfaceRawData, 49 IOI43ResetMainboard, 40 IOI43Temperature, 40 IOI43WDActivate, 40 IOI43WDDeactivate, 41 IOI43WDTrigger, 41 IPCameraRawCommand, 73 IPCamFailoverNotification, 72 IPCamFailoverRestore, 73 IPSwitchOperation, 62 IrisClose, 32 IrisOpen, 32 IrisStop, 32 KeyPressed, 41 KeyReleased, 41 KillAllEvents, 62 KillEvent, 62 KillEventByID, 62 LenelAccessEvent, 45 LenelFireEvent, 46 LenelIntercomEvent, 47 LenelRawData, 47 LenelRefreshNames, 47 LenelSecurityEvent, 48 LenelVideoEvent, 48 LiveCheck, 62 LogBarcodeData, 58 LogBarcodeDataLPS, 58 LogNPRRecognition, 58 LPSPositionData, 44 LPSQueryPosition, 45 MakeCPAReferenceImage, 73 MediaChannelSetupInfo, 73 MoveToAbsolutePosition, 32MoveToBySpeed, 32 MoveToRelativePosition, 33 NPRRawData, 74 NPRRecognition, 74 ObtrackChannelCounter, 75 ObtrackChannelCounterThreshold, 75 ObtrackChannelSetCounter, 75 ObtrackFrameRawData, 75 ObtrackGroupCounter, 76 ObtrackGroupCounterThreshold, 76 ObtrackGroupSetCounter, 76 ObtrackObjectRawData, 77 ObtrackTunnelAlarm, 77 PanAuto, 33 PanLeft, 33 PanRight, 33 PanStop, 34 POSData, 50 POSStatus, 50 PPDeviceAlarm, 51 PPDeviceInput, 51 PPDeviceOffline, 52 PPDeviceOnline, 52 PPInterfaceOffline, 52 PPInterfaceOnline, 52 PPQueryInterface, 52 PPSetDeviceOutput, 52 PPSubcellAlarm, 53 PPZoneAlarm, 53 PrePosCallUp, 33 PrePosClear, 31 PrePosSave, 34 RedundantPowerFailure, 63 114 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 114 --- GEUTEBRUCKRedundantPowerOk, 63 ResetMainboard, 41 SafebagClose, 35 SafebagData, 36 SafebagOpen, 36 SafebagPassingOfRiskData, 37 SafebagPassingOfRiskStart, 37 SafebagPassingOfRiskStop, 37 SceneStoreModification, 88 SensorAlarmFinished, 77 SensorAudioAlarm, 19 SensorInhibitAlarmFinished, 78 SensorInhibitVideoAlarm, 78 SensorVideoAlarm, 78 SetCameraText, 34 SetClientVCA, 71 SetClock, 63 SetDigitalOutput, 41 SetExportMarker, 54 SetLED, 41 SetLEDBlink, 42 SetSystemTime, 79 SetTestPictureMode, 79 SetupChanged, 64 SetupUploadProgress, 64 SetWatchdog, 64 SkidataControl, 55 SkidataDeviceEvent, 55 SkidataEntry, 55 SkidataExit, 55 SkidataTransaction, 56 SMRPViewerCleared, 63 SMRPViewerConnected, 63 SMTPMailSend, 63StartAutoBackup, 26 StartEvent, 64 StartRemoteExport, 54 StartSceneStore, 54 StopAllEvents, 65 StopEvent, 65 StopEventByID, 65 SystemError, 65 SystemInfo, 65 SystemSettingsChanged, 66 SystemStarted, 66 SystemTerminating, 66 SystemWarning, 66 Temperature, 42 TerminalArticleData, 50 TerminalPaymentData, 51 TiltDown, 34 TiltStop, 34 TiltUp, 35 TransferBinaryBuffer, 67 TransferBinaryChannelBuffer, 67 UserLogin, 67 UserLoginFailed, 67 UserLogout, 68 VCAlarmQueueConfirm, 81 VCAlarmQueueConfirmByIn- stance, 81 VCAlarmQueueConfirmByType, 81 VCAlarmQueueNotification, 88 VCAlarmQueueRemove, 82 VCAlarmQueueRemoveByIn- stance, 82 VCAlarmQueueRemoveByType, 82 VCAlarmQueueSelect, 82 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 115 --- Page 115 --- GEUTEBRUCKVCAlarmQueueSelectByInstance, 82 VCAlarmQueueSelectByType, 82 VCASetArmed, 79 VCAStatusAnswer, 79 VCAStatusRequest, 79 VCChangeSceneByName, 83 VCClearSceneByName, 83 VCFullMode, 83 VCSceneChanged, 88 VCSetAudioLevel, 83 VCShowViewerText, 83 VCStretchMode, 83 VideoContrastDetected, 79 VideoContrastFailed, 80 VideoSetImageBrightness, 80 VideoSetImageContrast, 80 VideoSetImageSaturation, 80 VideoSourceChanged, 80 VideoSyncDetected, 81 VideoSyncFailed, 81 ViewerChangeScene, 84 ViewerClear, 84 ViewerCleared, 88 ViewerClearScene, 84 ViewerClearTextOutput, 84 ViewerConnect, 84 ViewerConnected, 89 ViewerConnectLive, 85 ViewerExportPicture, 85 ViewerJumpByTime, 85 ViewerMaximize, 85 ViewerPlayFromTime, 85 ViewerPlayModeChanged, 89 ViewerPrintPicture, 86ViewerSelect, 86 ViewerSelectionChanged, 89 ViewerSetPlayMode, 86 ViewerShowAlarmByInstance, 86 ViewerShowAlarmByKey, 86 ViewerShowAlarmByType, 87 ViewerSyncAudioAndVideo, 84 ViewerTextOutput, 87 WatchdogActivate, 42 WatchdogDeactivate, 42 WatchdogTrigger, 42 ZoomIn, 35 ZoomOut, 35 ZoomStop, 35 116 GEVISCOPE actions – overview – v. 2.95 – September 5, 2013 --- Page 116 ---